Glentronics Pro Series Instruction Manual & Safety Warnings
  1. Manuals
  2. Brands
  3. Glentronics Manuals
  4. Water Pump
  5. PRO Series
  6. Instruction manual & safety warnings

Glentronics Pro Series Instruction Manual & Safety Warnings

Battery backup sump pump system
Hide thumbs Also See for Pro Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Battery Backup
Sump Pump
System
Instruction Manual
& Safety Warnings

Table of Contents

Instructions
1
1
1
Items Included in System
2
2
2
2
Installation Options
3
4
5
6
Hookup to Existing Discharge for
Narrow Sumps
7
Preparation of the Battery
8
9
9
9
IMPORTANT: Even if you have the Pro Series 1730 Backup Sump
Pump System installed by someone else, you must read and follow
the safety information contained in this manual. Failure to do so
could result in property damage, serious injury, or death.
9
9
Lights and Alarms
10
10
10
10,11
11
11
12
12
12
12,13
Testing the System
13
13
Technical Support
13
14
14

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Pro Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Glentronics Pro Series

Summary of Contents for Glentronics Pro Series

  • Page 1: Table Of Contents

    Hooking Up the Pump Installing the Battery Fluid Sensor Warranty IMPORTANT: Even if you have the Pro Series 1730 Backup Sump Pump System installed by someone else, you must read and follow the safety information contained in this manual. Failure to do so...

  • Page 2: Important Safety Warnings And

    • NEVER smoke or allow a spark or flame in the DANGER Wheeling, IL 60090 vicinity of the battery. • Use the Pro Series 1730 control unit for Risk of electrical and fire hazard. May result in death, serious injury, shock or burns. charging a LEAD-ACID battery only. Do not...

  • Page 3: Introduction

    Should any malfunction or emergency Fluid Sensor occur that involves the sump pump, the battery, or the AC power, your Pro Series 1730 system will sound an alarm. A light on the display panel of System Specifications the control unit will indicate the cause of the Pump alarm and the corrective action.

  • Page 4: Pump & Pipe

    PUMP Page 6 Page 5 If the direct discharge method is not possible or convenient, the Pro Series pump can be hooked NARROW SUMP PIT up to the same line as your AC sump pump by INSTALLATIONS installing a “Y” connector and two check valves.

  • Page 5: Direct Discharge To Outside

    BUILDING (Diagram A) check valve is used, a 1/8” hole must be drilled should the need arise. in the PVC pipe 3” above the Pro Series pump. DANGER sDANGER If a hole is not drilled above the pump, an air...

  • Page 6: Hookup To Existing Discharge

    6. Connect a 1 ⁄ ” diameter discharge pipe above attached to the elbow on the pump. the check valve of the Pro Series pump, and FLOOR attach a 45º elbow to that pipe. Extend JOIST 2. (a) Install a check valve on the PVC pipe another piece of pipe to reach the “Y”...

  • Page 7: Direct Discharge For Narrow Sumps

    BUILDING FOR NARROW SUMP PITS is attached to the elbow on the pump. be drilled in the PVC pipe 3” above the Pro Series installation, as long as you use less (Diagram C) pump. If a hole is not drilled above the pump an air than 20 feet of pipe.
  • Page 8 ⁄ ” diameter discharge pipe above Unplug the main AC pump when installing the the check valve of the Pro Series pump, and backup pump to avoid electric shock. Failure attach a 45º elbow to that pipe. Extend to do so could cause serious injury or death.

  • Page 9: Battery Instructions

    10 minutes and get medical attention. Review the safety instructions on page 1. A new Pro Series 2200 Standby Battery will run this system for a minimum of 7.5 hours continuously. 1. Remove the battery box top by pushing in the...

  • Page 10: Control Unit Hookup

    1. CAUTION When you position the control unit, be sure the PUMP If you are not using the Pro Series battery, you CHARGER charger cord will reach the AC power outlet and cannot use the battery fluid sensor. However...

  • Page 11: Understanding The Warning

    When another charger is used, first disconnect Warnings & Alarms conditions still exist. the Pro Series charger from the control unit, and The Pro Series 1730 is equipped with a then disconnect the control unit from the computer-controlled automatic charging system.

  • Page 12: Replacing The Battery

    1. Unplug the AC pump from the wall outlet. then lifting up. 2. Unplug the Pro Series pump from the back of the control unit. 3. Fan the area around the top of the battery with a piece of cardboard (or another non- 3.

  • Page 13: Water Alarm

    The alarm will sound when the sensor is outlet is operating, but the POWER warning light is removed. still on, replace the charger unit with Pro Series part number 1015001. 3. Unscrew the six battery caps. Add distilled water to each cell. If distilled water is not available;...

  • Page 14: Test-Reset-Silence Button

    You can receive technical support, parts or 5. Plug the pump wires into the back of the switch periodically. service information by calling Glentronics, Inc. control panel. at (800) 991-0466 or visiting the website at Lift the float up and let go. This will activate www.basementwatchdog.com.

  • Page 15: Quick Reference Guide

    Battery is damaged or old ....Replace battery bill of sale or receipt to the address listed below. Glentronics, Inc., at its option, will either repair or replace the product and return it postage prepaid.
  • Page 16 © 2003, Glentronics, Inc. 1806015...

This manual is also suitable for:

1730

Table of Contents