Related Manuals for Banner K50Z
Summary of Contents for Banner K50Z
- Page 1 K50Z Multipoint Sensor Instruction Manual Original Instructions p/n: 239895 Rev. C June 04, 2024 © Banner Engineering Corp. All rights reserved.
-
Page 2: Table Of Contents
Configuration Tools ...................................... 23 Cordsets ........................................23 Brackets........................................24 Chapter 9 Product Support Clean with Compressed Air ..................................25 Repairs ........................................25 Contact Us ........................................25 Banner Engineering Corp. Software Copyright Notice ..........................25 Banner Engineering Corp Limited Warranty..............................25 ... -
Page 3: Chapter 1 Product Description
These points are used to calculate and track meaningful values such as nearest distance or average distance. The sensor uses infrared light that is reflected back to an imager with 64 measurement points to evaluate targets in a large area. The sensor can be configured by IO-link or in the Banner Measurement Sensor software. It has two outputs that can be set up independently of one another. -
Page 4: Features And Indicators
• Easily monitor device status via the software • Visualize the application in real-time • Make adjustments to sensor settings on the fly For more information, visit www.bannerengineering.com/us/en/products/sensors/software/ banner-measurement-sensor-software.html. page 4 June 04, 2024 © Banner Engineering Corp. All rights reserved. -
Page 5: Chapter 2 Installation Instructions
Detection Position: Side View Detection Position: Overhead View A = Pixel one detected; pixel two not detected because mid-point is outside the 3D ROI, pixel three not detected because it is out of the 3D ROI (see "Discrete 1 Tab" on page B = Pixels one and two detected because both midpoints are inside the 3D ROI; pixel three is not detected because it is outside of the 3D ROI C = Pixels one, two, and three detected because the target is closer and all pixel midpoints are inside the 3D ROI (see "Field of View Charts" on page June 04, 2024 page 5 © Banner Engineering Corp. All rights reserved. -
Page 6: Wiring
Mount the device (or the device and the bracket) to the machine or equipment at the desired location. Do not tighten the mounting screws at this time. Check the device alignment. Tighten the mounting screws to secure the device (or the device and the bracket) in the aligned position. page 6 June 04, 2024 © Banner Engineering Corp. All rights reserved. -
Page 7: Chapter 3 Getting Started
Navigate to and open the downloaded file. Click Install to begin the installation process. Depending on your system settings, a popup window may appear prompting to allow Banner Measurement Sensor to make changes to your computer. Click Yes. Click Close to exit the installer. -
Page 8: Software Overview
K50Z Multipoint Sensor Instruction Manual Getting Started Software Overview Easy setup and configuration of range, sensitivity, and output using the Banner Measurement Sensor software and Pro Converter Cable. Banner Measurement Sensor Software Navigation toolbar—Use this toolbar to connect to the sensor, to save or load a configuration, or to reset to factory defaults ... -
Page 9: Chapter 4 Banner Measurement Sensor Workspace
Select to perform a factory reset on the sensor. All custom parameters will be lost From the Help menu, the following option is available: About Select to view the software version number, the copyright notice, and the warranty. June 04, 2024 page 9 © Banner Engineering Corp. All rights reserved. -
Page 10: Observation Space
3D ROI Displays a customizable 3D box that represents the active sensing area for that output. The sensor will not account for pixels outside of this area for its measurement. page 10 June 04, 2024 © Banner Engineering Corp. All rights reserved. -
Page 11: Summary Pane
Slow: Longer shutter for improved repeatability and accuracy in low excess gain Speed (ms) Resolution Fast Medium Slow Standard 8×8 Reduced 4×4 Sensor Polarity Define the output and remote input signal type. Sensor Lockout Enable or disable the remote input wire. June 04, 2024 page 11 © Banner Engineering Corp. All rights reserved. -
Page 12: Discrete 1 Tab
ON at the switch point, and OFF at the hysteresis. Switch Point - Background Ref: Creates a single switch point with the hysteresis set closer to the sensor. The output turns ON at the hysteresis and OFF at the switch point. Window: Creates two switch points forming window limits with the hysteresis on the outside of the window. Complementary: Output 2 will be the opposite of Output 1. Pulse Pro/PFM: PulsePro/PFM output to interface with Banner lights or a PLC with Pulse Frequency Modulated (PFM) inputs. page 12 June 04, 2024 © Banner Engineering Corp. All rights reserved. -
Page 13: Live Sensor Data Controls
50 Hz or 650 Hz (user defined in the software) represents a loss of signal condition where there is no target or the target is out of range. This output can be tied directly to a number of Banner lights for visual feedback without the need for a controller. -
Page 14: Chapter 5 Configuring A Sensor
The remote input wire is disabled by default. Pulse the remote input wire 10 times or use the Banner Measurement Sensor software to enable the feature. After enabling the remote input feature, pulse the remote input according to the diagram and the instructions provided in this manual. - Page 15 The power LED and all output LEDs continuously flash five Five-pulse the remote input. times, pause, flash five times, pause, and the sequence continues. Select the desired response speed. June 04, 2024 page 15 © Banner Engineering Corp. All rights reserved.
-
Page 16: Io-Link Interface
This information can be easily read and processed by the user. Each device can be unambiguously identified via the IODD as well as via an internal device ID. Download the K50Z's IO-Link IODD package (p/n 238988) from Banner Engineering's website at www.bannerengineering.com. -
Page 17: Factory Default Settings
Configuring a Sensor K50Z Multipoint Sensor Instruction Manual To reset using the Banner Measurement Sensor software, go to Sensor › Factory Reset. The sensor indicators flash once, the sensor is reset back to the factory default settings, and a confirmation message displays. To reset using the remote input, eight-pulse the remote input to apply the factory default settings. Factory Default Settings General Tab Default Settings... -
Page 18: Chapter 6 Specifications
Output LEDs: Amber, discrete output status PFM, Dual Discrete, IO-Link Construction Flatness (Pixel to Pixel Accuracy) Housing: Polycarbonate 20 mm Window: Polycarbonate Communication Protocol Lens Cover: Acrylic with optical coating IO-Link June 04, 2024 page 18 © Banner Engineering Corp. All rights reserved. -
Page 19: Fcc Part 15 Class A For Unintentional Radiators
Cet appareil est conforme à la norme NMB-3(A). Le fonctionnement est soumis aux deux conditions suivantes : (1) ce dispositif ne peut pas occasionner d'interférences, et (2) il doit tolérer toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité du dispositif. June 04, 2024 page 19 © Banner Engineering Corp. All rights reserved. -
Page 20: Pc Requirements
500 MB Available USB port Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. IMPORTANT: Administrative rights are required to install the Banner Measurement Sensor software. Dimensions All measurements are listed in millimeters [inches], unless noted otherwise. page 20 June 04, 2024... -
Page 21: Field Of View Charts
Specifications K50Z Multipoint Sensor Instruction Manual Field of View Charts Distance X/Y Field of View (mm) X/Y Pixel Length(mm) 1000 1500 1242 Z - Distance 2000 1657 June 04, 2024 page 21 © Banner Engineering Corp. All rights reserved. -
Page 22: Chapter 7 Update The Software
1, above, to update the software. Navigate to and open the file BannerMeasurementSensorSoftwareInstaller.exe. Depending on your system settings, a popup window may appear prompting to allow Banner Measurement Sensor software to make changes to your computer. Click Yes. Click Close to exit the installer. -
Page 23: Chapter 8 Accessories
2 = White ø 14.5 3 = Blue BC-M12F5-22-10 10 m (30.81 ft) 4 = Black 5.7 mm dia 5 = Gray BC-M12F5-22-15 15 m (49.2 ft) 6.35 mm 50.8 mm June 04, 2024 page 23 © Banner Engineering Corp. All rights reserved. -
Page 24: Brackets
Brackets 4X Ø5.5 4X Ø3.25 SMBK50RA • Right-angle bracket • 14-gauge 304 stainless steel 2X Ø6.5 SMBAMSK50R • Adjustable mounting bracket • 14-gauge 304 stainless steel 8X Ø3.5 2X M6 x 1 BHCS page 24 June 04, 2024 © Banner Engineering Corp. All rights reserved. -
Page 25: Chapter 9 Product Support
Banner minimum systems requirements. The above limitations apply even if Banner and its affiliates and channel partners have been advised of the possibility of such damages. This Agreement sets forth the entire liability of Banner, its affiliates and your exclusive remedy with respect to the software use. - Page 26 PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty.
- Page 27 LinkedIn Twitter Facebook © 2024. All rights reserved. www.bannerengineering.com...
Need help?
Do you have a question about the K50Z and is the answer not in the manual?
Questions and answers