Subscribe to Our Youtube Channel
Related Manuals for Moxa Technologies IMC-11 Series
Summary of Contents for Moxa Technologies IMC-11 Series
- Page 1 IMC-11 Series Quick Installation Guide Moxa Industrial Media Converter Version 1.1, January 2021 Technical Support Contact Information www.moxa.com/support 2021 Moxa Inc. All rights reserved. P/N: 1802000110001 *1802000110001*...
-
Page 2: Package Checklist
Overview The Moxa Industrial Media Converter IMC-11 series consists of entry-level 10/100BaseT(X) to 100BaseFX media converters that provide a cost-effective solution, and are specially designed for reliable and stable operation in harsh industrial environments. IMC-11 accepts either a 12 to 48 VDC power input. It operates reliably in a temperature range from -10 to 60°C, and IMC-11’s rugged hardware... - Page 3 Panel Layout of IMC-11 Series 1. Grounding screw 2. Terminal block for power input and grounding 3. DIP switch 4. Moxa Logo 5. Power input LED 6. 100BaseFX (SC/ST connector) port 7. FX port’s 100 Mbps LED 8. FX port’s FDX/COL LED 9.
-
Page 4: Mounting Dimensions
Mounting Dimensions IMC-11 series (10/100BaseT(X) to 100BaseFX) (unit=mm) DIN-rail Mounting The aluminum DIN-rail attachment plate should be fixed to the back panel of the IMC-11 when you take it out of the box. If you need to reattach the DIN-rail attachment plate to the IMC-11, make sure the stiff metal spring is situated at the top. -
Page 5: Wiring The Power Inputs
You should also pay attention to the following points: • Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point. NOTE: Do not run signal or communications wiring and power wiring in the same wire conduit. -
Page 6: Communication Connections
Communication Connections IMC-11 has one 10/100BaseT(X) Ethernet port. RJ45 Ethernet Port Connection The 10/100BaseT(X) port located on IMC’s front panel are used to connect to Ethernet-enabled devices. Below we show pinouts for both MDI (NIC-type) and MDI-X (HUB/Switch-type) ports, and also show cable wiring diagrams for straight-through and cross-over Ethernet cables. -
Page 7: Dip Switch Settings
This is a Class 1 Laser/LED product. To avoid causing serious damage to your eyes, do not stare directly into the Laser Beam. DIP Switch Settings IMC-11 Series (10/100BaseT(X) to 100BaseFX) DIP Switch 1 (Default OFF: FDX) FDX: Fiber port in full duplex mode... -
Page 8: Led Indicators
IMC-11 to activate the new setting. LED Indicators The front panel of Moxa Industrial Media Converter contains several LED indicators. The function of each LED is described in the table below. IMC-11 series (10/100BaseT(x) to 100BaseFX) Color State Description AMBER Power is being supplied to the power input. -
Page 9: Auto Mdi/Mdi-X Connection
Auto-negotiation and Speed Sensing Moxa IMC-11 series’ RJ45 Ethernet port supports auto-negotiation in 10BaseT and 100BaseT(X) modes, with operation governed by the IEEE 802.3u standard. This means that some nodes could be operating at 10 Mbps, while at the same time, other nodes are operating at 100 Mbps. -
Page 10: Specifications
If a Moxa Industrial Media Converter RJ45 Ethernet port is connected to a non-negotiating device, it will default to 10 Mbps speed and half-duplex mode, as required by the IEEE 802.3u standard. Specifications Technology Standards IEEE802.3, 802.3u, 802.3x Interface RJ45 Port 10/100BaseT(X) Fiber Port 100BaseFX (SC, ST connectors available) - Page 11 EN61000-4-4 (EFT) Level 2 EN61000-4-5 (Surge) Level 2 EN61000-4-6 (CS) Level 2 Shock IEC 60068-2-27 Free Fall IEC 60068-2-32 Vibration IEC 60068-2-6 Warranty 5 years Federal Communications Commission Statement FCC - This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the IMC-11 Series and is the answer not in the manual?
Questions and answers