Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Maxxus BENCH PRESS PRO
Summary of Contents for Maxxus BENCH PRESS PRO
- Page 1 BENCH PRESS with safety bars PRO...
- Page 2 Repairs Contract / Notification of Damage Claim © 2023 by MAXXUS Group GmbH & Co. KG All rights reserved This publication may not be reproduced, stored in retrieval system, or transmitted on whole or in part, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Maxxus Group GmbH &...
-
Page 3: Safety Instructions
We recommend placing MAXXUS® floor protection mats permanently under the device. Please ensure that these mats cannot slip or slide. − Do not put this training device on pale or white coloured carpets or rugs as the feet of the device may leave marks. − Make sure that your training device is kept out of contact with hot items and is kept at a safe distance from any sources of heat e.g. - Page 4 Any manipulation of or interference with the device can cause damage to the device and be a danger to people. If you have any questions or queries contact your specialist dealer or the MAXXUS Service Team and they will be pleased to help you further.
-
Page 5: Assembly Step
Assembly Assembly Step 1 Lock 2pcs of Pre-assembled part assembly (A) and Connected assembly (No.3) well with 6pcs External hexagon screw M10*100 (No.10), 12pcs Arced washer φ10 (No.15) and 6pcs Locking nut M10 (No.16) as shown in the picture. Assembly Step 2 Lock Pre-assembled part assembly (B) and Main frame reinforcing plate (No.5) well with 4pcs External hexagon screw M10*60 (No.9) 8pcs Flat washer φ10 (No.14) and 4pcs Locking nut M10 (No.16) as shown in the picture. - Page 6 Assembly Assembly Step 3 Lock Back cushion (No.6) and Head cushion(No.7) into Pre-assembled part assembly (B) with 8pcs External hexagon screw M8*20 (No.11) 1pcs External hexagon screw M8*60 (No.13) and 9pcs Flat washer φ8 No.12 as shown in the picture. Step 4 Assembly Step 4 Lock 4pcs of Pre-assembled part assembly (C) into 2pcs of Pre-assembled part assembly (A) with 8pcs External...
- Page 7 Assembly Assembly Step 5 Insert Spring clamp (φ50) (No.8) into Hang barbell rod tube assembly (No.23) as shown in the picture. Insert Spring clamp （φ50）(No.8) into Hang barbell rod tube assembly (No.23) as shown in the picture.
-
Page 8: Recommended Accessories
Alternatively, you can use the MAXXUS® degreaser spray (optionally available). After this, dry the e MAXXUS® degreaser spray (optionally available). After this, dry the guide pipes off thoroughly and lubricate them with guide pipes off thoroughly and lubricate them with MAXXUS® lubricant spray (optionally available) leaving AXXUS®... -
Page 9: Training Recommendations
Training Recommendations Training Recommendations Preparation Before Training Before you start training make sure that not only your training device is in perfect condition, your body must also Preparation Before Training be prepared for training. Therefore, if you have not done any endurance training for some time, you should con- Before you start training make sure that not only your training device is in perfect condition, your body must sult your GP and undergo a fitness check-up. -
Page 10: Training Frequency
Training Recommendations Intake of Liquids The intake of sufficient liquids before and during training is vital. During a 60-minute training session it is Training Recommendations possible to lose up to 0.5 litres of liquid. To compensate for this loss, you can drink a mix of one third apple Intake of Liquids juice to two thirds water to replace all electrolytes and minerals which your body loses through sweat. - Page 11 Part list Parts List Part name Qty. Part name Qty. Main frame assembly Support frame assembly Connected assembly Hang barbell rod assembly Main frame reinforcing plate Back cushion Head cushion Spring clamp （φ50） External hexagon screw (M10*60) External hexagon screw (M10*100) External hexagon screw (M8*20) External hexagon screw (M8*60) Flat washer （φ8）...
- Page 12 Pre-assembled parts Pre- assembled part assembly Pre- assembled part assembly Pre- assembled part assembly Pre- assembled part assembly Pre- assembled part assembly...
-
Page 13: Exploded Drawing
Exploded Drawing Exploded diagram... -
Page 14: Warranty
The warranty period for your training device starts on the date of purchase and applies solely to products which were purchased directly from the MAXXUS Group GmbH & Co. KG, or one of the MAXXUS Group GmbH & Co. KG direct and authorised distribution partners. - Page 15 Ich erkenne die Allgemeinen Geschäftsbedingungen der MAXXUS Group GmbH & Co. KG an. Falle einer vor Ort-Reparatur sind unsere Mitarbeiter inkassoberechtigt. Mit meiner Unterschrift bestätige ich I hereby instruct the company MAXXUS® Group GmbH & Co. KG to repair the above defects. In Warranty cases I will not be charged diese Vereinbarung.
- Page 16 Maxxus Group GmbH & Co. KG Nordring 80 w D-64521 Groß-Gerau E-Mail: info@maxxus.de www.maxxus.com...
Need help?
Do you have a question about the BENCH PRESS PRO and is the answer not in the manual?
Questions and answers