Related Manuals for Total TS526043
Summary of Contents for Total TS526043
- Page 1 1.新产品 1.修改零部件清单 更 改 记 录 T0122.V01 2022.1.4 T0622.V02 2022.6.7 版本号 版本号 日期 设计师 日期 设计师...
- Page 2 TABLE SAW TS526043,UTS526043 SCAN FOR VIDEO TOTAL TOOLS WORLD 2600W...
- Page 3 Double insulated for additional protection. Read the instruction manual before using. CE conformity. Wear safety glasses, hearing protection and dust mask. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
- Page 4 . Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. Cluttered and dark areas invite accidents.
- Page 5 Use of an RCD reduces the risk of electric shock. A moment of inattention while operating power tools may result in serious personal injury. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
- Page 6 and must be repaired. Such preventive safety measures reduce the risk of starting the power tool accidentally. Power tools are dangerous in the hands of untrained users. Many accidents are caused by poorly maintained power tools. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
-
Page 7: Residual Risks
Residual risks Even when the power tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the power tool’s construction and design: a) Health defects resulting from vibration emission if the power tool is being used over longer period of time or not adequately managed and properly maintained. -
Page 8: Specifications
SPECIFICATIONS Model TS526043 UTS526043 220-240V~50/60Hz 110-120V~50/60Hz Rated Power 2600W 2600W Blade size 90° 86 mm 3-19/50 ting 45° 60 mm 2-9/25 No load speed (/min) 4800 4800 Main table size 25-3/10 able size (left) 25-3/10 65 mm able size (right) -
Page 9: Additional Safety Rules
is unintentionally contacted. blade immediately. 19. CHECK DAMAGED PARTS. Before further use Clean the spindle, flanges (especially the of the tool, a guard or other part that is installing surface) and hex nut before installing damaged should be carefully checked to the blade. - Page 10 Freehand means using your hands to support or guide the work piece, in lieu of a rip fence or miter gauge. 19. NEVER reach around or over saw blade. NEVER reach for a work piece until the saw blade has completely stopped.
-
Page 11: Installation
(3) Connect another set of upper long rod UP-A and SAVE THESE INSTRUCTIONS. lower long rod D-C to the side frame and fix them with WARNING: half-round head square neck screws and flange lock nuts. WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. - Page 12 nut onto the arbor, making sure that the teeth of the 2. Riving Knife Positioning and Blade blade are pointing down at the front of the table. installing Always install the hex nut with its recessed side facing the outer flange. Riving Knife Positioning 1.
- Page 13 Raise the blade up to maximum elevation. Adjust the 3. Blade Guard Installation rip fence, align the front and back pointer in 0 scale. WARNING: Tighten the back lock screw and press down the lock lever. • Raise the blade up to maximum elevation before install blade guard.
-
Page 14: Functional Description
1. Restart FUNCTIONAL DESCRIPTION button 2. Switch ON CAUTION: button 3. Switch OFF • Always be sure that the tool is switched off and button unplugged before adjusting or checking function on the tool. Adjusting the depth of cut 1. Handle wheel To start the tool, press the switch ON button. -
Page 15: Operation
1.Saw Sub table (back) blade 1. Screws 2.Wrench 2. Sub table 3.Open- (back) end wrench 4.Auxiliary fence 5.Rip fence 6.Miter scale Push sticker can be stored on the left side of the base. Saw blade, wrenches, auxiliary fence, rip fence and To use the sub table (back), loosen the screws on the miter gauge can be stored at the right side of the base. - Page 16 lock auxiliary fence. Ripping 1. Auxiliary CAUTION: fence 2. Half- • When ripping, remove the miter gauge from the table. round head square neck • When cutting long or large work pieces, always bolt provide adequate support behind the table. 3.
-
Page 17: Maintenance
Use of miter gauge Replacing carbon brushes 1. Miter Remove and check the carbon brushes regularly. gauge Replace when they wear down to 3 mm (1/8") in length. 2. Knob Keep the carbon brushes clean and free to slip in the holders. - Page 18 TS526043,UTS526043 Exploded view...
-
Page 19: Part Description
TS526043,UTS526043 Spare part list Part Description Qty NO. Part Description PUSH STICK SLIDING BAR PAN HEAD SCREW M6X55 MAIN TABLE PAN HEAD SCREW M6X60 POINTER WASHER 6( 6.5× ×1) PULLEY LEFT GUARD PULLEY SCREW ×35 FIX PLATE BLADE GUARD SUPPORT ARM... - Page 20 TS526043,UTS526043 Spare part list Part Description NO. Part Description DUST BAFFLE 2 HALF-ROUND HEAD SQUARE NECK BOLT M6×25 SCREW M5×10 HEX SOCKET HEAD SCREW M6X20 BEARING BOX CABINET BALL BEARING 6203RS AUXILIARY FENCE LEFT FIX PLATE RETAINING RING 10 AUXILIARY FENCE RIGHT FIX PLATE...
- Page 21 TABLE SAW www.totalbusiness.com TOTAL TOOLS CO., PTE. LTD. No. 45 Songbei Road , Suzhou Industrial Park , China. MADE IN CHINA T0622.V02...
Need help?
Do you have a question about the TS526043 and is the answer not in the manual?
Questions and answers