Table of Contents
Advertisement
Quick Links
CineLink 4K-E4 & 4K-E2 Quick Start Guide
This Quick Start Guide provides the steps required to install and connect your CineLink 4K-E-Loop IP
encoders.
Note
This Quick Start Guide applies to both the CineLink 4K-E4 and 4K-E2 encoders.
CineLink 4K-E-Loop IP encoders stream low-latency 4K video, feature zero-latency HDMI loop-outs and
are managed with Haivision Command 360 software.
For Command 360 configuration and operation information, refer to the
General Guidelines
Use the following guidelines when unsafe conditions exist or when potentially hazardous voltages are
present:
•
Always use caution and common sense.
•
To reduce the risk of electrical shock, do not operate equipment with the cover removed.
•
Repairs must be performed by qualified service personnel only.
Improper handling and/or installation practices of sensitive equipment may VOID the warranty.
Warning
Only trained and qualified personnel should install, replace, or service this equipment.
ATTENTION Seul le personnel spécialisé et qualifié est habilité à effectuer l'installation, le
remplacement et l'entretien de cet équipement.
Command 360
CineLink 4K-E4 & 4K-E2 Quick Start Guide
CineLink 4K-E4 & 4K-E2
1
www.haivision.com
User's
Guide.
Generated on: 2024-03-06 20:45:16
HVS-ID-QSG-CineLink4KE
Advertisement
Table of Contents
Related Manuals for Haivision CineLink 4K-E4
Summary of Contents for Haivision CineLink 4K-E4
- Page 1 Note This Quick Start Guide applies to both the CineLink 4K-E4 and 4K-E2 encoders. CineLink 4K-E-Loop IP encoders stream low-latency 4K video, feature zero-latency HDMI loop-outs and are managed with Haivision Command 360 software. For Command 360 configuration and operation information, refer to the User's Guide.
- Page 2 Warning Any power supply shipped with a CineLink is to be used only with that product. Haivision supplied power supplies are not for general use. ATTENTION Tout bloc d'alimentation électrique livré avec un CineLink doit être utilisé uniquement avec ce produit.
-
Page 3: Anti - Static Precautions
à la terre. Si aucun bracelet n'est disponible, touchez périodiquement une surface métallique non peinte de l'équipement. N'utilisez jamais d'outil conducteur, tel qu'un tournevis ou un trombone, pour régler les commutateurs ou interrupteurs. Command 360 Generated on: 2024-03-06 20:45:16 CineLink 4K-E4 & 4K-E2 Quick Start Guide HVS-ID-QSG-CineLink4KE... - Page 4 EMC Warnings Notice with respect to Class A (FCC) Changes to equipment without the permission of Haivision may result in its failure to comply with the FCC requirements for Class A digital devices. If applicable, your rights to use the equipment may be limited by the FCC rules and you may be able to remedy, at your own expense, any interference with...
- Page 5 à la terre. Si aucun bracelet n'est disponible, touchez périodiquement une surface métallique non peinte de l'équipement. N'utilisez jamais d'outil conducteur, tel qu'un tournevis ou un trombone, pour régler les commutateurs ou interrupteurs. Command 360 Generated on: 2024-03-06 20:45:16 CineLink 4K-E4 & 4K-E2 Quick Start Guide HVS-ID-QSG-CineLink4KE...
-
Page 6: Technical Specifications
1 x 3.5 mm stereo mic in Outputs/Loop-Out Output/Loop-Out 4 x HDMI 2.0 with audio support 2 x HDMI 2.0 with audio support Networking Connectivity Network Connector 2 x RJ45 Command 360 Generated on: 2024-03-06 20:45:16 CineLink 4K-E4 & 4K-E2 Quick Start Guide HVS-ID-QSG-CineLink4KE... - Page 7 Dual density unit can power up to eight devices simultaneously. Power Consumption S-C360-CL-4KEL2: 5 amps at @ 12V DC S-C360-CL-4KEL4: 5.5 amps at @ 12V DC Operating Temperature 0 to 40 °C Command 360 Generated on: 2024-03-06 20:45:16 CineLink 4K-E4 & 4K-E2 Quick Start Guide HVS-ID-QSG-CineLink4KE...
-
Page 8: Physical Installation
Unpack the box and position the hardware on a stable work surface. Optionally, mount the device in a server rack. Note The CineLink 4K-E4 and 4K-E2 encoders are indoor appliances and should be kept in a dry, dust free environment. Caution When mounting in a server rack, refer to your rack vendor's documentation as well as the included rack mount instructions in the rail kit provided with your system. -
Page 9: System Interfaces
The following LED indicator is located on the front of the encoder: LED Indicator Description Power The power indicator lights when the encoder is connected to a power source. Back Command 360 Generated on: 2024-03-06 20:45:16 CineLink 4K-E4 & 4K-E2 Quick Start Guide HVS-ID-QSG-CineLink4KE... -
Page 10: Obtaining Documentation
For more information, please visit our website at: https://www.haivision.com/environment. Obtaining Documentation This document was generated from the Haivision InfoCenter. To ensure you are reading the most up-to- date version of this content, access the documentation online at https://doc.haivision.com. You may generate a PDF at any time of the current content. See the footer of the page for the date it was generated.
Need help?
Do you have a question about the CineLink 4K-E4 and is the answer not in the manual?
Questions and answers