The Learning Feature; Programming The Volume Control Function - THOMSON 23LB220S4 Manual

IFC228-LCD_EN
5/07/04 13:26
Getting started

The Learning feature

The Learning feature completes the programming procedure
described on page 5, as it enables you to record the functionality
of a specific button from the original remote control to one of the
TV's remote control buttons.
Notes:
- Before using the Learning feature, make sure this TV's remote
control is programmed to control other appliances you have
connected to the TV. Programming the remote control erases all
learned commands for that appliance mode.
EN
- You cannot record a learned function to the following buttons on
the TV's remote control:
EXIT , and LIGHT
- The remote control functions are recorded (learned) by sending
infrared (IR) signals: this operation should be carried out in a dimly
lit room to avoid interference. Make sure the TV's remote and the
original remote are no more than 5 cm apart, with the Infrared (IR)
transmitter of the original remote facing the IR receiver on the top
of the TV's remote.
- The learned buttons are mode specific—if you add a button
function from your DVD player's remote control, you must press the
DVD button first before the learned function will work (in TV mode,
the button where you've stored the learned function will continue to
work as it always has).
- Certain remote controls do not support the use of the Learning
function.
Adding a Learned Function
1.
On the TV remote, press and hold the appliance button that
applies to the function you will be adding (
AMP AUX
, or ).The appliance button lights up. Press and
REC
hold the button.
2.
The appliance button lights turn on, then off. Release both
buttons.The relevant appliance button light remains on.
3.
On the TV's remote control, press the button where you want
to store the new function (the appliance button turns off and
then back on).
Note: If you press an invalid button on the TV remote, the appliance
buttons flash several times to alert you.You'll have to repeat step 3.
4.
Press and hold the button of the appliance's remote control
that has the functionality you are recording to the TV's remote
control. Keep pressing the button until the TV remote's
appliance button light turns off and back on.The function has
been saved to the TV remote.
Note: if it is not possible to programme this function the appliance
buttons flash several times.You'll have to repeat step 3.
5.
Repeat this procedure to add more functions. Or, press
to exit learning mode.
Note: If you want to assign a new function to a button already
programmed, you must record over it.
Clearing a Learned Function
1.
Press and hold the relevant appliance button (the appliance
button lights up).Then press and hold the
2.
The appliance buttons turn on. Release the appliance and
EXIT
buttons (the appliance button being unprogrammed
remains on). Remote is now in Clear learned function mode.
3.
Press the button where learning is to be cleared.The appliance
button flashes off then back on—the learned function was
cleared successfully.
Page 6
TV VCR DVD AUX SAT AMP
, , , , ,
.
DVD VCR
,
EXIT
button.
4.
Repeat steps 1 through 3 to clear more learned functions.
Note: If an invalid button is pressed, the appliance mode button(s)
flashes 4 times to alert you. Repeat step 3.
5.
EXIT
Press the button and your TV remote returns to its
original operating mode.
Deleting ALL Learned Functions
1.
Press and hold the
button lights up.Then press and hold the
,
2.
The appliance button lights turn on, then off. Release both
buttons.The current appliance button light remains on.
3.
Press any appliance button to delete all learned functions in all
modes.

Programming the volume control function

If you have programmed the TV remote control to use with other
appliances and these are connected to an amplifier you can also
programme the remote control to adjust the volume when you
are using one of these appliances.The example below describes
the procedure for programming a DVD player.
1.
Programme the AMP
with the amplifier (refer to page 5).
2.
Move the remote control away from the appliances. Press the
- button and while holding it down, press the relevant
SAT
, ,
mode button ( DVD
Release the - button.
3.
Switch on the amplifier, then the DVD player.
4.
Set the remote control to
volume using the
Repeat this operation for the other appliances.
To cancel the programmed function for any of the appliances, press
the - button, while holding it down and enter the code 000
using the numeric buttons.
EXIT
6
EXIT
button.The current appliance
button.
button on the remote control to use
, in this example), then the AMP
DVD , play a disc and adjust the
+/- buttons.
button.