DELTA DORE Delta 8000 TAP RF Installation Instructions Manual
Hide thumbs
Also See for Delta 8000 TAP RF:
- Instructions for use manual (10 pages) ,
- Installation instructions manual (11 pages)
Related Manuals for DELTA DORE Delta 8000 TAP RF
Summary of Contents for DELTA DORE Delta 8000 TAP RF
- Page 1 Delta 8000 TAP RF Programmable thermostat for Delta 8000 system Installation instructions...
-
Page 2: Table Of Contents
Contents 1/ Installation ..............4 2/ Association of the thermostat with the wireless gateway .......... 7 3/ Thermostat configuration ........8 4/ Setting the clock ............12 5/ Locking down settings .......... 14 6/ Return to initial settings ........15 6.1 Initialising the thermostat parameters ..... 15 6.2 Deleting the association of the thermostat with the wireless gateway .... -
Page 3: 1/ Installation
1/ Installation Since the temperature measurement sensor is inside the box, you must install the thermostat: - wall-mounted or placed on a shelf or a piece of accessible furniture at a height of 1.50 m. - away from heat sources (fireplaces, sunlight) and draughts (windows, doors) IMPORTANT: Do not install the thermostat on a wall in contact with the outdoors or with an unheated room (e.g. -
Page 4: 2/ Association Of The Thermostat With The Wireless Gateway
2/ Association of the thermostat with the wireless gateway ❶ On the gateway: Press and hold the left ❼ The screen displays CF20. hand side button for 3 seconds until LED Press OK to open the setting, then press 1 flashes, then release. + and - to select the output with which the room thermostat will be associated. -
Page 5: 3/ Thermostat Configuration
3/ Thermostat configuration ❶ Turn the selector knob to Correction of the +/- 5°C in increments of measured temperature 0.1°C (0°C by default) ❷ Press OK. Setting display Temperature displayed (default selection) ❸ The screen displays CF01. (after activating the Display of the measured thermostat) temperature. - Page 6 3/ Thermostat configuration Activation of the door/window magnetic contact function Not activated (the room thermostat switches to Frost Protection mode Active (default selection) - Display of the symbol if the door/window magnetic contact is activated). Not flashing This menu is only available if CF06 = 1. symbol will flash in the event of detection.
-
Page 7: 4/ Setting The Clock
4/ Setting the clock ❶ Turn the selector knob to ❷ Set the year with + and - and confirm with OK. ❸ Set the day and month with + and - and confirm with OK. ❹ Set the hour value with + and - and confirm with OK. ❺... -
Page 8: 5/ Locking Down Settings
5/ Locking down settings 6/ Return to initial settings 6.1 Initialising the thermostat parameters From the modes. This menu restores the system to factory settings. Press and hold the 'i' button for 5 seconds. symbol appears. ❶ From the (or OFF) mode. Simultaneously press the 1st and 4th buttons from the left ( ) for In Lock mode, only the Information button ( i ) is active. -
Page 9: Deleting The Association Of The Thermostat With The Wireless Gateway
6/ Return to initial settings 6.2 Deleting the association of the thermostat with the wireless gateway ❶ Turn the selector knob to ❷ Press and hold the 2nd button from the left for 3 seconds. >3s >3s Release. >3s ❸ The screen displays Ln01. Press + to display Ln03. -
Page 10: 7/ Troubleshooting
7/ Troubleshooting 8/ Technical characteristics • Power supplied by 2x 1.5V batteries, type LR03/AAA (provided), • The screen displays the symbol. The batteries are spent. Replace the batteries or Lithium 1.5 V, LR03 (AAA), 1200 mAh, • Type 1 automatic action When a defect is detected on the system, the symbol flashes on •... - Page 11 www.deltadore.com...