Hidden And Advanced Features; Features And Where They Are Found; Programmable Sensor Override; Cycle And Soak - Hunter ICC2 Owner's Manual

FEATURES AND WHERE THEY ARE FOUND

1. Programmable Sensor Override: Hold
Start Times.
2. Cycle and Soak: Hold +
PRG
cycle time and Press
3.
Delay Between Stations: Hold
4. Hide Programs: Hold
5. Solar Sync Delay: Hold
6. Clik Delay: Hold + and turn to System Off.
7. Total Run Time: Turn to Run Times. Press
Station 1. Press PRG to view other programs.
8. Test Program: Hold PRG
9. Easy Retrieve™ Memory: Hold
PRG
and to restore.
10. Total Reset: Hold PRG
11. QuickCheck™ Technology: Hold +, -, ◄, ►, together. Press
+ to begin check.
12. Run Program: Hold ►
Press ► to advance stations.

PROGRAMMABLE SENSOR OVERRIDE

The ICC2 Controller allows the user to program the
controller so a sensor response is independent from station
to station. This feature allows the sensor to disable watering
for only the desired stations (as opposed to the entire
system). For example, patio gardens or other landscapes
that are underneath overhangs or roofs may not receive
water when it rains and will still need to be watered during
periods of rain.
Note: The controller default setting is "ON," which means
the sensor is active and will disable watering on all zones
once the sensor is triggered.
1. With the dial in the Run position, press and hold the
button, turn the dial to the Start Times position, and
–
release the button.
2.
The display will show the station number, and "ON" will
flash. Press the + and
sensor for the station shown.
ON = sensor enabled (will suspend irrigation)
OFF = sensor disabled (will allow watering)
Built on Innovation
®
- and turn to
and turn to Run Times. Enter
to set soak time.
-
and turn to Run Times.
- and turn to Water Days.
+ and turn to Solar Sync.
◄ from
for 3 seconds.
+ and PRG to save. Hold
and Reset button.
and press PRG to select program.
– buttons to enable or disable the

Hidden and Advanced Features

3. ►
Use the and
station for Sensor Override.
4. Rotate the dial back to the Run position when finished
programming all Sensor Overrides.

CYCLE AND SOAK

The Cycle and Soak feature allows you to split a station's run
time into cyclical, shorter watering durations. This feature
is useful when applying water to slopes and tight soils
because it automatically slows the application of water by
irrigating with multiple shorter cycles, as opposed to one
long run time. This helps to prevent runoff and excessive
watering.
To do this, you should enter the Cycle time as a fraction of
the station's total desired watering time and the Soak time
-
as the minimum amount of time required before watering
can occur again for the next cycle. The total number of
cycles is determined by taking the total programmed
station run time, and dividing it by the Cycle time.
For example, Station 1 requires 20 minutes of watering, but
after 5 minutes, runoff occurs. However, after 10 minutes,
all water is absorbed into the soil. The solution would be to
program 20 minutes for the station Run Time, 5 minutes for
the Cycle time, and 10 minutes for the Soak time. This would
create four separate cycles of watering, with 5 minutes per
cycle, and 10 minutes of soak time in between watering.
However, if there are stations programmed to run after
Station 1, the Cycle and Soak process won't complete
until the end of all scheduled zones. This means that after
Station 1 runs its first cycle, the controller will proceed
sequentially in numerical order until all programmed
stations complete their run times. Then, the program will
revert to Station 1 and complete its remaining cycle and
soak schedule.
1. To access the Cycle and Soak menu, begin with the dial in
the RUN position. Press and hold the
dial to the Run Times position, and release the
–
2. Initially, Station 1 will display. To access other stations,
press the ►
shown, use the
the Cycle time. The user can set the Cycle time from
1 minute to 4 hours or OFF if no Cycle and Soak
is desired.
Note: When setting both Cycle and Soak times, any times
less than 1 hour will only display the minutes (e.g., 30). For
times greater than 1 hour, the display will change to include
the hour digit (e.g., 2:45).
◄
buttons to scroll to the next desired
or ◄ buttons. Once the desired station is
+ and – buttons to increase or decrease
+
button, turn the
+ button.
29