Important Installation Information - LEGRAND Wattstopper LMDM-601-W Quick Start Manual

Dlm wireless dimming wall switch

Hide thumbs

page of 6

/ 6
Bookmarks

WIRELESS ROOM CONNECTION

LMRC-611MCC

LMDM-601

Wireless

Dimmer

Sensor Params

LMPX-600

LMPC-600

Mode

Auto On

Blink

Load Type Dim

DLM Configuration App

on a mobile device

Distance Recommendations:

30' max between LMDM-601 and mobile device

60' max. between LMDM-601 and room controller or bridge

To ensure a successful installation and startup of a wireless system, the following steps must be taken by the

installing contractor. Failure to document all device address and locations may delay completion of startup

and result in additional startup charges.

Key Requirement: Document every Device's MAC Address (at least the last 4 alphanumeric characters). An

additional MAC address label is included for the installer to use on a floor plan map. The last four characters are

repeated in a larger font, in bold. Keep this document so that the commissioning tech has access at a later date.

Pair wireless devices to a room controller to create an individual room network and enable Plug N' Go operation.

Device pairing can be done by using Push-to-Pair (PtP) mode on the room controller and all other wireless devices, or by using the

DLM Config App.

To pair devices in a network, they must all have the same wireless channel and Network ID. By default the channel is 15 and the

Network ID is 1. Using Push-to-Pair mode, the Network ID for all devices being paired is migrated to a new number, so that only those

device communicate with each other. The channel number will remain at 15.

Push-to-Pair in a room with a single LMRC-611 Room Controller

NOTE: Once you enter PtP mode on the room controller, a three minute timer begins. If the Config button on any device in the room is

pressed, the timer resets and begins the three minute countdown again. If no Config button is pressed within three minutes, the

room controller will exit PtP mode.

1. Enter PtP mode on the room controller. Press the Config button three times (within three seconds) until the LED on the room

controller flashes green.

2. Enter PtP mode on the LMDM-601. Using a pointed tool, press the Config button three times. As with the room controller, the

LED on the switch will flash green.

3. Pair the LMDM-601. Press the Config button on the LMDM-601 one more time to pair it to the room controller. The load connected

to the room controller will toggle once (if the load is OFF, it will turn ON; if ON, it will turn OFF) to indicate that pairing was

successful. Also, the LMDM-601's blinking LED will turn to solid green as another indicator of a successful pairing.

NOTE: If there are any wireless sensors, dimmers, or additional switches in the room, repeat steps 2 and 3 for each of

those devices so that all devices are paired together in the same network. For each device, the load will toggle during

step 3 and its config LED will turn solid green.

4. Exit PtP mode. From any device, press the Config button 3 times. After a few seconds, the LED on each Room controller, switch

or sensor currently in PtP mode will flash white and reboot, leaving the default network and migrating to the new network. Then,

the LED on the room controller will flash blue and the pairing process finishes.The default Network ID on all devices will change to

a new number, based on the last four digits of the Mac address on the room controller, and now those devices will communicate

only with each other and not any devices which have not been paired.

NOTE: It is important to exit PtP mode within the three minute time limit mentioned above. If you do not, none of the device

pairings will be remembered and you have to start the process over from the beginning.

IPv6 Wireless communication

between DLM Room devices

over 6LoWPAN

IPv6 Mesh

Bluetooth low energy

communication for

mobile App support

Wireless

Sensor and/or

Photosensor