Advertisement
Quick Links
*911402-00*
33/35A Series
911402-00
Rim Exit Device
Installation Instructions
Devices covered by these instructions:
33/35A Rim Exit Device
33/35A-F Rim Exit Device
CD33/35A Rim Exit Device
QEL33/35A/-F Rim Exit Device
SS33/35A/-F Rim Exit Device
HW33/35A Rim Exit Device
HW33/35A-F Rim Exit Device
Dogging Key
(use with non-fire devices
to lock down pushbar)
For hurricane rated device requirements, see page 2.
Digital instructions -
please read
For the best installation experience
we now have Smartphone friendly
digital interactive instructions.
Just scan the QR code.
alle.co/33rim
Customer Service
© Allegion 2021
Printed in U.S.A.
1-877-671-7011
www.allegion.com/us
911402-00 Rev. 08/21-g
Advertisement
Related Manuals for Allegion Von Duprin 33/35A Series
Summary of Contents for Allegion Von Duprin 33/35A Series
- Page 1 For hurricane rated device requirements, see page 2. Digital instructions - please read For the best installation experience we now have Smartphone friendly digital interactive instructions. Just scan the QR code. alle.co/33rim Customer Service © Allegion 2021 Printed in U.S.A. 1-877-671-7011 www.allegion.com/us 911402-00 Rev. 08/21-g...
- Page 2 Hurricane rated exit device requirements (when used with approved Allegion door applications) Application Single door, standard strike Mullion Double door, standard strike 4954 or KR4954 1654 or KR1654 1606 33A/35A 5654 (Wind Only) 5754 1408 33A/35A-F 299F 9954 or KR9954...
-
Page 3: Screw Chart
SCREW CHART Screw Application Device Subassembly Trim mount or sex bolts: ¹⁄4 -20 x1” (25 mm) ³⁄4 ” (44 mm) door ¹⁄4 -20 x 1- ¹⁄2 ” (38 mm) ¹⁄4 ” (57 mm) door Metal door surface mount #10-24 x 1” (25 mm) (Yellow) ¹⁄4 #10 x 1... - Page 4 Draw horizontal device and strike center lines ( C L ). Install strike using two screws only at this time. Panic Device Install strike 1/16” past door side of stop * 39¹³⁄16” (101.1 cm) from finished floor For double doors with a 1439 Strike (standard) mullion and strike already installed, use existing...
- Page 5 If using a 1439 strike, install wear strip. If not, go to Prepare lock side of door for device and trim. step 5. See trim instructions for Door pull side door preparation. side Wear strip See template for drill and cut-out information A.
- Page 6 If necessary, cut device. Install hinge stile mounting bracket. Prepare device for cutting Mark and prepare 2 mounting holes Mounting Tape bracket flush Anti-rattle clip (remove while cutting, then 1/4” drill inside replace after cutting) 13/32” drill outside Cover plate (flush to pushbar) 13/32”...
-
Page 7: 499F Strike Installation
Install 2 support screws and center case cover Install 2 support screws and center case cover End cap Remove protective film from pushbar For fire devices only use #8-32 machine thread screw. Center 2 support case cover screws 499F STRIKE INSTALLATION 1. -
Page 8: Optional Equipment
OPTIONAL EQUIPMENT CD (Cylinder Dogging) Option Undog... -
Page 9: Frame Preparation
1439 Strike 1439 Strike Frame Preparation RHR shown #25 Drill (LHR opposite) #10-24 tap 1/8” Drill pilot 1” deep 7/16” 1-9/16” to 7/16” Blade stop face of door... - Page 10 299/299F/1606 Strike Template 299F 1606 Strike Door Door Door Mullion Stop Stop Cut paper along this line and place on door stop against edge of door (see picture below) #25 Drill #10-24 tap 1/8” Drill pilot 1” deep Template 1-1/16” 1-1/16”...
- Page 11 33/35A Rim device Line X-X is a reference line for trim and exit device alignment. C L of device Line X-X shown here should Template correspond to line X-X in the trim installation instructions 1/4” Holes - 2 places #25 drill inside #10-24 tap 1/8”...
- Page 12 33/35A Rim device Line X-X is a reference line for trim and exit device alignment. Line X-X shown Device Template here should correspond to line X-X in the trim installation instructions 1/4” Holes - 2 places #25 drill inside #10-24 tap Cut-out device side only 1/8”...
Need help?
Do you have a question about the Von Duprin 33/35A Series and is the answer not in the manual?
Questions and answers