Advertisement
Quick Links
ASSEMBLY AND INSTALLATION INSTRUCTIONS
Model 1425 Aluminum Swivel Rack
IMPORTANT
BEFORE YOU BEGIN
Read these instructions and
warnings completely before
installation.
BOLT KIT
Bolt kit #32-0021 is provided with
your rack. Check this bolt kit to be
sure the following parts are in-
cluded:
Qty.
Description
4
5/16-18 x 1-1/4" Hex Hd Bolt
20
5/16" Flat Washer
2
5/16-18 x 3" Hex Hd. Bolt
14
5/16-18 Nylon Lock Nut
8
5/16-18 x 1-1/4" Carriage Bolt
1
Tube, Sealant - Clear
* See back page for Bolt Chart
TOOLS REQUIRED
• Electric drill
• 3/8" Drill Bit
• 1/2" Open or Box End Wrench
• 3/8" Drive Ratchet
• 1/2" Socket
• Hammer
• Center Punch
• Hacksaw
• Ruler
• Pencil
• Straight Edge - 2' long
CAPACITY
200 lbs.
MAXIMUM
This product is only intended for, and only safe for, transporting
ladders. It is the responsibility of the user to secure the ladder to
the rack before transporting. Any modifications made to this
product, or use of this product for any other purpose than its in-
tended use, will create a hazardous condition that will cause
serious personal injury or property damage.
3
NOTE: This product is to be
installed only on all-steel
service bodies
WARNING
Part No. 24-0145 REV. B ECN 5315 05/13
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Weather Guard 1425
Summary of Contents for Weather Guard 1425
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS Model 1425 Aluminum Swivel Rack IMPORTANT CAPACITY BEFORE YOU BEGIN NOTE: This product is to be 200 lbs. installed only on all-steel MAXIMUM service bodies Read these instructions and warnings completely before installation. BOLT KIT Bolt kit #32-0021 is provided with your rack.
- Page 2 Refer to this illustration for part identification Support Angle (2) Top Front Stand (1) Collar (1) Rear Stand (1) Strap, 1450 (2) Lower Front Stand (1) Figure 1. Parts Identification...
-
Page 3: Assembly And Installation Instructions
ASSEMBLY AND INSTALLATION INSTRUCTIONS CAUTION To keep debris out of your eyes when drilling, always wear protective eyewear. NOTE: To prevent rust from occur- ring, touch-up any drilled holes. Pre-drilled holes for 16" height 1. Front Stand Height - Front Stand is pre-drilled for 16" and 30"... - Page 4 Approximately 2" Figure 4. Roof clearance Upper Front Stand 2. Front Stand Assembly - Fasten the Upper Front Stand to the Lower Front Stand through either the 5/16" Flat top or bottom set of holes, or the holes Washer you drilled ( See Figure 5. ). Do not (4 places) tighten the bolt for the slot completely, Collar...
- Page 5 3. Support Angle Marking - The Front Stand will be located as shown in Figure 6. when installed. From the inside of the service body "side box", position a Support Angle in the front upper corner, against the top and end panel of the box ( See Figure 7.
- Page 6 CAUTION Prior to drilling, so as not to cut electric wires, etc., check the vehicle for locations. 4. Drilling - Drill the marks with a 3/8" drill bit. NOTE: When installing the Front and Rear Stands, be sure to use the sealant provided under all external fasteners, as well as the mounting bases of the Stands.
- Page 7 Direction of swivel Passenger Side Front of service body Outside of service body Figure 10. Front Stand Installed (shown on passenger side) Drain hole 6. Rear Stand Mounting - Fasten the Rear Stand to the service body with the upright tube drain hole towards the rear of the vehicle ( See Figure 11.
- Page 8 If you have any questions, please give us a call. Call Toll Free 1-800-456-7865 Weather Guard® products are protected by one or more of the following patents or trademarks: U.S. - 842268, 1661625, 1663369, 1750034, 2362167; Canada - 282725; U.K. - 1400720;...
Need help?
Do you have a question about the 1425 and is the answer not in the manual?
Questions and answers