Advertisement
Table of Contents
TRUCK STORAGE SOLUTIONS
SECURING YOUR REPUTATION
ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS
BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT.
MODEL
1345-52-02 Compact Steel Truck Rack (1,000 lb. Rating)
Note:
X represents the color code for your model: 0 = Clear | 3 = White | 5 = Black | 52 = Matte Black
NOTICE
There may be left over components depending on up-fit. Any modification
or unintended use of this product shall immediately void all manufacturer's
warranties. Manufacturer disclaims all liability for injuries to persons or
property resulting from any modification to, or unintended use of this
product.
DANGER
Danger of explosion. Do not use this product for storing or transporting
flammables, explosives, hazardous materials, or hazardous waste, such as
containers of gasoline, solvents, gun powder, dynamite, propane tanks,
acetylene tanks and cutting torches.
©2019 Werner Co.
INSTALLATION MANUAL
STEE
PROTECT R L
COMPACT TRUCK RACK
PACK RAT
DRAWER UNITS
®
®
ROT
R
®
CAUTI
ON
To keep debris out of your eyes when checking the underside of the vehicle, or
when drilling, always wear protective eye wear. Never load your rack to exceed
the safe rated capacity of your vehicle. Heavy loads carried high can
dangerously alter the center of gravity.
WARNING
Always place and tightly secure ladder on rack with a sufficient barrier
(tape/padding) between the ladder and rack. Failure to properly secure the
ladder on the rack while in transit could cause damage leading to structural
collapse of the ladder and potential injury or death. This product is only
intended for, and only safe for, transporting ladders, lumber, pipe and other
similar materials. It is the responsibility of the user to secure these materials
to the rack before transporting. Any modifications made to this product, or
use of this product for any other purpose than its intended use, could create
a hazardous condition that can cause serious personal injury or property
damage. This product is only intended and safe for use in storing and
transporting small tools, equipment and other similar materials.
Any modifications made to, or unintended use of this product, could create a
hazardous condition that can cause death, serious personal injury or
property damage.
WEATHERGUARD.COM
WEATHERGUARD.COM
WEATHERGUARD.COM
Part No.24-00082 REV. B ECO 105234 2/4/19
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Weather Guard 1345-52-02
Summary of Contents for Weather Guard 1345-52-02
- Page 1 BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT. MODEL 1345-52-02 Compact Steel Truck Rack (1,000 lb. Rating) Note: X represents the color code for your model: 0 = Clear | 3 = White | 5 = Black | 52 = Matte Black...
-
Page 2: Tools Required
TOOLS REQUIRED • Rubber Mallet • Allen Key (1/8”, 7/32”, 5/16”) • Utility Knife • Open End Wrench (9/16”, 3/4”) PARTS LIST (8) 1/2-13 x 3” (4) 1/2-13 x 4" (12) 3/8-16 x 2-1/2" (18) 3/8-16 x 1” (8) No Drill Bolt Bolt Bolt... -
Page 3: Rack Assembly
Assembly Recommendation: 1) If user plans on carrying ladders, it is recommended to reverse the carriage bolts to have the bolt head on the inside of the rack. 2) Before applying protective strip, make sure cross members are clean and clear of any debris. RACK ASSEMBLY Silicone Application: STEP 1... - Page 4 STEP 7 Install center cross member, the cross member without the Weather Guard® logo, to one of the front legs using (2) Part C, (2) Part L, and (2) Part F. Tilt the assembly up and balance the assembly on the legs while installing to the opposite front leg using (2) Part C, (2) Part L, and (2) Part F.
- Page 5 STEP 8 Repeat step 6 with the rear cross member, making sure the Weather Guard® logo faces upright and towards the tailgate. Use locking pins (Part H) instead of nuts and bolts. REAR CROSS MEMBER REAR RACK ASSEMBLY STEP 9 Install front hoop, making sure the air foil is pointing STEP 10 Install support brackets if the truck is less than 8’...
-
Page 6: Rack Installation
STEP 11 Apply the rubber protective strip to the STEP 12 Insert all 8 plastic plugs top of each of the cross members. (Part I) into the holes of the front legs. RACK INSTALLATION STEP 13 Install the front (cab side) mounting feet to the truck bed. Place the mounting foot onto the truck bed placing the foot as far forward as possible. - Page 7 STEP 14 Install rear (tailgate side) mounting feet to the truck bed. It is recommended to use the single center hole in the mounting pad for securing the rear feet when possible. (If the vehicle is a 2016 or newer Chevrolet/GMC truck refer to Step 13). Insert the hardware, using (1) Part J, (1) Part C, and (1) Part M, into the stake pocket and thread the stake pocket bracket (Part J) to the end of the bolt.
- Page 8 11. Vehicle stability could be greatly reduced in the event that too much weight is placed on rack and vehicle. The rating of the rack may be greater than the vehicle’s load ratings. Weather Guard recommends consulting the vehicle manufacturer before loading material for assistance.
- Page 9 WEATHER GUARD® Product or (b) replacing the entire WEATHER GUARD® Product. In addition, the Manufacturer may elect at its option, not to repair or replace the WEATHER GUARD® Product, but rather issue to the original purchaser a refund equal to the purchase price paid for the WEATHER GUARD®...
Need help?
Do you have a question about the 1345-52-02 and is the answer not in the manual?
Questions and answers