7.12 - General purpose - Novice guide 8 - VArIOUS WINDOWS 3 - FLIGHT 8.1 - Accounts 3.1 - Download the X-Hubsan 2.0 Application 8.2 - Flight log 3.2 - Main interface guide 8.3 - Search for drone 3.3 - Drone and Radio Control Pairing 8.4 - Web site...
This product is not suitable for children under 14 years of age. While using one or more Hubsan products, users also accept all responsibility for their behaviours, actions as well as any consequences resulting from their use.
To avoid damage, do not operate the Drone with broken or damaged components. MAINTENANCE Do not attempt to open or repair the drives yourself. Please contact Hubsan technical support or an authorized reseller directly for assistance. For more information, visit the official website at www.hubsan.com.
If you plan not to fly the Drone for a long period, it is advisable to keep the battery at approximately 50% charge to maintain performance and battery life batteries. Use Hubsan charger for battery charging. Discharge the battery at a temperature no lower than 5°C. To avoid discharge complete and therefore damage the battery, do not prolong the discharge time.
1. DrONE 1. DrONE 1.1 - Done pats 1.1 - Done pats Popelle A 3 axis Gimbal Popelle B Camea 4K HD Engine Smat Battey Foot (with antenna) Battey level indicato Gimbal potection Powe button Done body USB Pot...
Page 8
Battey fixing clips TF cad slot Sensos fo altitude hold at low altitude Gound vision senso VPU LED landing light fo night flight The aircraft, when in operation and after the flight, generates heat. Avoid holding the drone with your hands in the part underneath where the alu- minum heat sink is housed, to avoid burns.
IrCrAFT BATTErY IrCrAFT BATTErY 1.2.1 Battey chaging 1.2.1 Battey chaging The capacity of the lithium battery of the drone is 3000 mAh, for a voltage of 7.2 V, the standard version is supplied without a charger therefore it is sufficient, to charge the battery with a phone charger with Micro USB adapter, the time of charging, a 2A charger, and about 2.5 hours.
1.2.3 Intelligent battey functions 1.2.3 Intelligent battey functions 1) Powe display: The battery has a power indicator, which can display the battery power. 2) Battey stoage potection: After the battery is fully charged and stored for 10 days without any use, it will automatically turn into self-discharge mode to protect it- self (there may be slight heating during discharging).
Make sure to fully charge the battery each time before flying the Drone. The flight battery must use a dedicated Hubsan power adapter for charging. 1 - If the temperature of the intelligent flight battery is high at the end of the flight it must be cooled to room temperature before charging.
8) Button to record videos 9) Gimbal adjustment 10) Programmable button 11) Antennas 12) Smartphone connection cable 13) Mini USB port for battery charging and connection. 14) Hole for lanyard. 15) Compartment for storing sticks 16) Compartment for storing the USB...
2.2 radio contol functions 2.2 radio contol functions rADIO CONTrOL DrONE FUNCTIONS Climb The power stick is used to make the drone ascend or descend. Pushing the stick forward makes the Drone go up, pushing it back makes the Drone go down. When the stick is in the central position the Drone maintains height.
rADIOCONTrOL DrONE FUNCTIONS Long press to start recording, short press to end Video recording. Gimbal adjustment Check the angle of the gimbal joint. Press and hold the FN button, rotate the gimbal ad- justment wheel to adjust the brightness of the re- mote control display.
radio Contol Diagam radio Contol Diagam Done battey level Infomation aea Speed mode Flight height State of the popelles Flight distance GPS satellites locked Compass calibation Done contol signal Done speed radio contol battey level Photo / Video Heading angle Angle of the radio Contol antennas Angle of the radio Contol antennas 1 - Adjust the angle of the an-...
radio contol calibation radio contol calibation 1 - Pull both joysticks to the top left corner and simultaneously press and hold the power button to turn on the Remote Control, release the power button and the sticks after hearing the Remote Control emits some beeps. 2 - Rotate both sticks to the maximum angle clockwise at least 3 times, then release the sticks.
Download the Applica- tion for free by scan- ning code shown on the side. QR code to download the X-HUBSAN 2.0 App for Android Alternatively, down- load it via the APPLE Store for IOS systems or with Google Play for ANDrOID systems.
2 - Press the remote control switch to connect to the mobile phone, and wait for the remote control to connect the aircraft in success. 3 - Open the mobile phone X-HUBSAN 2.0 APP, it will automatically jump out of the activation interface.
rONE CALIBrATION rONE CALIBrATION 3.4.1 Hoizontal calibation 3.4.1 Hoizontal calibation If during flight the drone shows significant horizontal deviation, land and disarm the engines. Place the drone on a perfectly level horizontal surface. Open the setting interface in the APP, select horizontal calibration.
3.4.3 Stating and stopping engines 3.4.3 Stating and stopping engines The conditions for starting the engines must be the following: 1 - The Drone, the Radio Control, the Smartphone or the Tablet must be connected; 2 - The Drone is calibrated with the compass (the App does not require calibration); 3 - The Drone must be positioned horizontally;...
FLIGHT CONTrOL MODE The flight controller analyzes the GPS signal and changes the corresponding modes The Drone uses GPS fixed points if the signal is optimal, it also uses the MODE assistance of the optical flow sensor for stable and precise flight. When the Drone is in flight and detects a poor GPS signal, it uses the optical stabilization mode.
Page 22
r T H P r O C E S S Make sure whose take-off point has been registered (Home) Activate the following parameters to perform RTH: 1 - Set the altitude of the done duing rTH; 2 - Activate the Landing Pad seach if necessay; Regardless of the flight altitude if the Drone is within 5 meters from the lan- ding base, it can land regularly;...
When the Drone is returning and at a height of approximately 10 meters from the ground, it will automatically search for the Landing Pad to perform the landing. The Gimbal does not take into account the take-off phase but only the landing phase. rEQUIrEMENTS OF LANDING PAD Sharp contrast between the bottom...
The Done is not de- signed to eplace the pilot's commands and assessments, pay at- tention to the suggestions of the X-HUBSAN 2 APP. The optical flow system cannot be used nomally in envion- ments with light that is too bight, too dak, specula, watey,...
FLIGHT MODE FLIGHT MODE 360° Shooting 360° Shooting 3 6 0 ° S h o o t i n g Select the direction of rotation: clockwise - anticlockwise Set the rotation angle and range (90° - 360°, accuracy +/- 1°) Set the rotation speed (1-30 sec., accuracy +/- 1s) Click GO, the Drone moves to the assigned position and will start filming and record- ing during rotation.
Click “Mode Selection”, then “Change Orbit” to set the current position or the center po- sition of the mobile device. During Orbit mode you can adjust the speed and direction of the Drone by moving the control stick left or right and adjust the radius of the Orbit by moving the control stick forward or backward.
Click on “Mode Selection”, then on “Line Fly Mode” to set the angle, distance and speed of the Drone. Orbit mode Line Fly Mode Angle: 0° Distance: 10m Relative altitude: 1.0m/s Speed: 1.0 m/s Route Preview S E T T I N G S A N D C O N F I G U r A T I O N S Set the angle (0 - 360°, precision +/- 1°);...
By choosing the Time-lapse mode you can choose the “free” or “circular” mode. Hyperlapse Mode T I M E - L A P S E M O D E ( F e e ) The Drone will take a certain number of photos and automatically compose the Time-lapse video based on the set parameters.
C I r C L E M O D E The Drone will take a certain number of photos and automatically compose the Time-lapse video based on the point of interest of the circle and the set parameters. While shooting, moving the sticks will automatically stop the activity.
CAMErA CAMErA Camea Settings Camea Settings Select the camera icon on the main in- terface of the App to set the resolution, white balance, color and other parame- ters. Hoverimg mode Video Resolution Frame Rate 30FPS Video Bitrate Grade: 5 White balance Automatic Color...
adjust angle of the Gimbal by rotating control wheel on the remote control. Stoing Images and Videos Stoing Images and Videos Via an external TF U3 memory card, which depending on the model purchased, can have a capacity of 16 GB, 32 GB, 64 GB or 128 GB. The system supports hot plugging, therefore it is possible to insert the TF Card even with the device turned on, however it is preferable to insert or disconnect the TF Card with the drone turned off.
Below are some of the easy-to-use App windows, the Home, Photo and Video Editor, Tutorial, Service, Ac- flight modes, Waypoint, Orbit, Follow me, etc., which count, Hubsan Official Site, Flight Log, etc. are explained in the previous pages. Settings e Calibations...
Contact Hubsan Customer Service if you cannot resolve the problem. The Done is not detected. Restart the Drone, the Radio Control and the X-Hubsan 2.0 App Try updating the Drone's firmware. Check if the LED on the side of the Drone is on; if it is flashing it means there is an anomaly.
Page 37
Check whether the lens and the sensors of the optical positioning system instal- led on the bottom of the Drone are clean and free of foreign bodies. Contact HUBSAN technical support team to resolve the problems, according to the corresponding inconveniences...
Team, for further information you will also be asked to fill a mandatory support form. rEFUNDS SErVICE a) - Within 7 days of delivery, Hubsan will accept items in new, unaltered condition and free of damage from the customer. b) - Within 7 days of delivery, Hubsan will accept items with obvious defects.
Page 39
- Any malfunction or damage caused by unauthorized use or modifications to the product, exposure to humidity, any contact with substances, such as water, oil, sand, detergents, etc. i) - After receiving a return confirmation from Hubsan, the product must be sent to our office within 7 days. VArIOUS a) - Payments by credit or debit card or PayPal may take up to 10 business days after the product has been received.
Hubsan warranty service team will investigate and identify the problem, once the product is received at our location, Hubsan will cover the cost of labor, materials, re- turn and shipping if the problem is found to be due to the quality of the our product.
Page 41
Hubsan within 7 days. PAID rEPAIr SErVICE Hubsan also provides paid repair services for customers who do not meet the require- ments for warranty, refund or replacement services. For paid repair service, you will be charged for diagnostics, labor, materials and shipping costs.
14 - The acquisition, through the use of Hubsan products (in particular, but not limi- ted to aircraft), of any data, audio, video that results in a violation of the law or...
Page 43
This poduct is not a toy Not suitable fo childen unde 14 yeas of age risk of battey explosion if eplaced with a non-oiginal Hubsan one. Dispose of used batteies accoding to local egulations. Keep all dangeous moving pats, especially popelles, away...
FCC INFOrMATION This equipment has been tested and found to comply with the limits for a Class B dig- ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.