Hubsan X4 User Manual
Hide thumbs
Also See for X4:
- Instruction manual (64 pages) ,
- Manual (40 pages) ,
- Installation instructions manual (24 pages)
Related Manuals for Hubsan X4
Summary of Contents for Hubsan X4
- Page 1 ® www.hubsan.com Ages 14+ Please read the instructions carefully before use. 2.4GHZ RC SERIES 4 CHANNEL 2.4GHZ RC SERIES 4 CHANNEL 2.4GHZ RC SERIES 4 CHANNEL ITEM NO.:H107 FLIP TIPS SEE PAGE 14-16...
-
Page 3: Table Of Contents
CHARGING THE LI-PO BATTERY off and on, the user is encouraged to try to correct the interference by one or more of the following measures: TRANSMITTER FLY THE X4 connected. ADVANCED PERFORMANCE SETUP void the user’s authority to operate the equipment. -
Page 4: Introduction
H107-A18 The X4 is powered by a Lithium-Polymer (LiPo) battery. Blue LEDs Red LEDs To avoid risk of fire or damage, never recharge your battery while it is inserted in the X4. maintain battery performance and life. H107-A44 4*AAA Rechargeable NI-MH battery（... - Page 5 Never charge the LiPo battery that has been punctured or damaged. 4) If the X4 still drifts to one side, add a few sheets of paper (the number of sheets will vary depending on the amount of drift) to the side of the X4 that drifts. The paper will help After a crash, inspect the battery pack for the sign of damage.
-
Page 6: Safety Check Before Flying
Be careful to keep your body and loose clothing away from the blades. Never take your eyes off the (1) Replace the motor. X4 or leave it unattended while it is turned on. Stop operating immediately if the X4 flies out of your (2) Resolder any broken motor connections. -
Page 7: Charging The Li-Po Battery
(1) Battery voltage is too low. (2) Pair the X4 with the transmitter again. (3) Land the X4 with the throttle stick in the full down position for 3 seconds and then take off again. 5. X4 won't perform flips. -
Page 8: Transmitter
White blade A Black blade A 7 Power Switch 5 Rudder Trim Black blade B Li-po battery 3 Aileron Trim Upper shell LED-2 Lower shell LED-1 Screw Rubber feet MODE 2 Screw H107 H107 THE HUBSAN X4 THE HUBSAN X4... -
Page 9: Removing And Installing Leds
2. Line up the LED to the round holder slot. Press the wires carefully into the slot and secure them neatly into the arm. Yellow Installation is complete H107 H107 THE HUBSAN X4 THE HUBSAN X4... - Page 10 Remove the propellers. Position the cover’s four holes with the motors. Press each of them onto the motors, then re-install the propellers in their correct positions on the X4 . When removing the protection cover, remove the propellers first as in the above steps, and pinch the protection cover from each motor.
- Page 11 The X4’s propellers are not identical. Each propeller is labeled with an A or B. When installing replacement propellers, be certain to install as shown below. The X4 will not fly, and will flip and blink. Do not move any other stick or trim before the crash if the propellers are not installed correctly.
- Page 12 MODE 2 MODE 1 Always disconnect the X4 battery plug after turning off the transmitter when you stop flying. 7.4.2 Right Flip Push the Aileron stick fully to the left and then quickly push it fully to the right. Release the stick to LED Indications the center after the flip.
- Page 13 6.2 Transmitter Sticks And X4 Control Responses You can also adjust sensitivity in Expert Mode following the Normal Mode procedure controls. CAUTION: To avoid loss of control, always move the transmitter sticks slowly. Be aware that during maneuvers.
- Page 14 (b) Elevator Sensivity Adjustment (a) Rudder Sensivity Adjustment 7.2 Normal and Expert Flight Modes The X4 is factory set for Normal Mode flying, and it will always power up in Normal Mode. Though Mode is activated. Flashing (c) Aileron Sensivity Adjustment...