To avoid injuries, do not fly a quad with broken or damaged components. Maintenance: Do not try to fix the quad by yourself. Please contact Hubsan directly or distributors authorized by Hubsan for technical support.
INTRODUCTION Thank you for buying a HUBSAN product. The H507A is designed to be an easy-to- use,multi-functional RC model, capable of hovering and acrobatic flight maneuvers. Please read this manual carefully and follow all the instructions. Be sure to keep this manual for future reference.
1-1 APP FUNCTIONS AND SETTINGS Flight Video Control Home Settings Signal Battery Signal Not connected Map Calibration Not connected Mode Swap Headless Location Virtual Joysticks Return to Home Auto take off/ Auto landing Toggling Functions: Virtual Joysticks On Virtual Joysticks Off Auto Take Off Auto Landing...
2-1 INTRODUCTION The quadcopter battery is a rechargeable Li-Po battery rated at 7.6V and has a 550mAh capacity. The battery should only be charged with the provided HUBSAN charger to avoid overcharging. Please make sure the battery is fully charged before use.
2-3 CHARGING Connect the battery to its USB charger, then connect the USB end either to a wall adapter or a USB device (such as a computer or mobile power charger (5V,1A)). The USB LED indicator blinks in red when charging, and turns solid after the battery is fully charged. Please unplug the charger and battery promptly afterwards.
Hubsan_h507a_XXXXXX NOTICE: For safety purposes, please do not use your smart device for other purposes while it is connected via the X-Hubsan APP to the copter. If you wish to control the quad with other devices, please restart the quad.
To avoid major in-flight issues) do not calibrate the compass near sources of magnetic interference. (1) Please follow the calibration instructions on the X-Hubsan APP. (2) Calibration is completed when the calibration instructions disappear. The APP will revert to its operation interface.
Page 10
Propeller B Propeller A Propeller A Propeller B “ ”Make “ D”Make “D”形口 <Figure 1> Attach the propellers to their corresponding motors (both propellers and motors should be marked A and B). Gently but firmly tighten the propellers with the screw-driver. Propellers should be firmly secured to the motor shaft but not completely deadlocked.
Make sure that the A and B propellers are installed correctly (to their ● corresponding motors). The X4 will not fly if propellers are improperly installed. ● Keep fingers and other body parts away from hazardous moving parts. Notice : Mind the corresponding colors of the A and B propeller screws! Propeller B Propeller A 6-2 REMOVING PROPELLERS...
6-3 INSTALLING PROPELLERS Use a screwdriver and gently tighten the screw counterclockwise for propeller A. Gently tighten the screw clockwise for propeller B. Propeller B Propeller A Counterclockwise Propeller A Propeller B Clockwise...
H507A TROUBLESHOOTING 1. No GPS Signal ! Make sure that you and the copter are outdoors. The flight environment must be open (without tall buildings or obstructions). 2. Altitude Hold & Positioning not work! Check that the quad has 6 or more GPS satellites. 3.
H507A SPARE PART CHART H507A-01 H507A-02 H502C-03 H507A-07 HT005 Relay Body Shell Lamp Base A/B Screw Li-Po Battery Transparent yellow H507A-03 H502-05 H502C-08 H502-19 H502-20 Propeller A/B Motor A USB Charger Screwdriver Propeller guard Yellow H502-06 H507A-04 H502-07 H502-08 H502-10 Motor B Motor Holder Grey Motor Holder...
INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 16
This is not a toy, not suitable for children under 14. WWW.HUBSAN.COM Product Name:X4 STAR PRO Company:Shenzhen Hubsan Technology Co., Ltd Address:13th Floor, Block 1, Tower C, Software Industry Base, Xuefu Road, Nanshan District, Shenzhen, China. Factory:Dongguan Tengsheng Industrial Co., Ltd.