Planet IGS-4215-8T4X Quick Installation Manual
Industrial l2/l4 managed gigabit switch with 10g uplink
Hide thumbs
Also See for IGS-4215-8T4X:
- User manual (353 pages) ,
- Quick installation manual (18 pages) ,
- Quick installation manual (15 pages)
Subscribe to Our Youtube Channel
Related Manuals for Planet IGS-4215-8T4X
Summary of Contents for Planet IGS-4215-8T4X
- Page 1 Industrial L2/L4 Managed Gigabit Switch with 10G Uplink IGS-4215-8T4X/IGS-4215-8UP4X Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ................. 3 2. Requirements ..................4 3. Wiring the Power Inputs ............... 5 3.1 Grounding the Device ..............6 4. Terminal Setup ..................7 4.1 Logging on to the Console .............. 8 4.2 Configuring IP Address via Console ..........8 4.3 Storing Current Switch Configuration .......... -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET L2/L4 Managed Gigabit Switch. The descriptions of these models are shown below: Industrial L2/L4 8-Port 10/100/1000T + 4-Port 10G SFP+ IGS-4215-8T4X Managed Ethernet Switch (-40~75 degrees C) Industrial L2/L4 8-Port 10/100/1000T 802.3bt PoE + IGS-4215-8UP4X 4-Port 10G SFP+ Managed Ethernet Switch (-40~75 degrees C) “Industrial Managed Switch” is used as an alternative name in this Quick Installation Guide. -
Page 4: Requirements
2. Requirements z Workstations running Windows 8/10/11, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP protocols. z Workstations are installed with Ethernet NIC (Network Interface Card) z Serial Port Connection (Terminal) The above Workstations come with USB ports. The above Workstations have been installed with terminal emulator, such as Tera Term or PuTTY. -
Page 5: Wiring The Power Inputs
3. Wiring the Power Inputs The Upper Panel of the Industrial Managed Switch indicates an inlet power socket and consists of one green terminal block connector with 6 contacts. Please follow the steps below to insert the power wire. Please follow the steps below to insert the power wire. 1. Insert positive/negative DC power wires into contacts 1 and 2 for Power 1 or 5 and 6 for Power 2. -
Page 6: Grounding The Device
1. The wire gauge for the terminal block should be in the range between 12 and 24 AWG. 2. The power input range of IGS-4215-8T4X is 9V ~ 48V DC and supports 24V AC. PWR1 and PWR2 must provide exactly the same DC voltage for power load balance while operating with dual power input. -
Page 7: Terminal Setup
4. Terminal Setup To configure the system, connect one end of a USB data cable to a USB port on a PC or notebook computer and the other end to the USB Type-C console port of the Industrial Managed Switch. PC / Workstation with Terminal Emulation Software USB Type C... -
Page 8: Logging On To The Console
Figure 4-3 appears. The following console screen is based on the IGS-4215-8UP4X. The display of the IGS-4215-8T4X is the same. Username: admin Password: admin Figure 4-3: Industrial Managed Switch Console Login Screen The user can now enter commands to manage the Industrial Managed Switch. - Page 9 Show the current IP address 1. At the “IGS-4215-8UP4X#” prompt, enter “show ip”. 2. The screen displays the current IP address, subnet mask and gateway as shown in Figure 4-4. Figure 4-4: IP Information Screen Configuration of the IP Address 3. At the “IGS-4215-8UP4X #” prompt, enter “configure”. 4. At the “IGS-4215-8UP4X (config)#”...
-
Page 10: Storing Current Switch Configuration
4.3 Storing Current Switch Configuration 1. At the “IGS-4215-8UP4X#” “copy running-config prompt, enter startup-config” as shown in Figure 4-6. Figure 4-6: The Configuration Save Screen If you are not familiar with console command or the related parameter, enter “?” anytime in console to get the help descrip- tion. -
Page 11: Starting Web Management
5. Starting Web Management The following shows how to start up the Web Management of the Industrial Managed Switch. Note the Industrial Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. - Page 12 3. After entering the password, the main screen appears as Figure 5-3 shows. Figure 5-3: Web Main Screen of Industrial Managed Switch (Using IGS-4215-8UP4X as an representative) The Switch Menu on the left of the Web page lets you access all the commands and statistics the Industrial Managed PoE+ Switch provides. Figure 5-4: Switch Menu Figure 5-5: Switch Sub-menu...
-
Page 13: Saving Configuration Via Web
Figure 5-6: Switch Sub-menu Now, you can use the Web management interface to continue the Switch management. Please refer to the user’s manual for more. 5.2 Saving Configuration via Web To save all applied changes and set the current configuration as a startup configuration, the startup-configuration file will be loaded automatically across a system reboot. -
Page 14: Restoring Default Configuration
6. Restoring Default Configuration IP Address has been changed or admin password has been forgotten – To reset the IP address to the default IP Address “192.168.0.100” or reset the login password to default value, press the hardware-based reset button on the front panel for about 10 seconds. After the device is rebooted, you can log in the management Web interface within the same subnet of 192.168.0.xx. -
Page 15: Customer Support
7. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team.
Need help?
Do you have a question about the IGS-4215-8T4X and is the answer not in the manual?
Questions and answers