Table of Contents 1. Package Contents ................. 3 2. Requirements ..................4 3. Wiring the Power Inputs ............... 5 3.1 Grounding the Device ..............7 4. Terminal Setup ..................8 4.1 Logging on to the Console .............. 9 4.2 Configuring IP Address via Console ..........10 4.3 Storing Current Switch Configuration ..........
2. Requirements Workstations running Windows XP/2003/Vista/7/8/10/2008/10/11, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP proto- cols. Workstations are installed with Ethernet NIC (Network Interface Card) Serial Port Connection (Terminal) The above Workstations come with COM Port (DB9) or USB-to-RS232 converter. The above Workstations have been installed with terminal emulator, such as Tera Term, PuTTY or Hyper Terminal included in Windows XP/2003.
Max. Fault Alarm Loading: 24V, 1A 1 2 3 4 5 6 PWR1 PWR2 Input: 48-54V , 7.5A max. Dual power input is required for maximum PoE loading. Refer to user’s manual for more details. Figure 3-3: IGS-4215-16P2T2S DC Inlet Power Socket...
Page 6
1. The wire gauge for the terminal block should be in the range from 12 to 24 AWG. 2. Please check the wire AWG Ampere specification before connecting PLANET Industrial Managed PoE+ Switch. PWR1 and PWR2 must provide exactly the same DC voltage for power load balance while operating with dual power input.
3.1 Grounding the Device Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device. Earth Ground Max. Fault Alarm Loading: 24V, 1A 1 2 3 4 5 6 DC Input: 48-54V , 6A max.
4. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to the RJ45 type of the console port of the Industrial Managed PoE+ Switch. PC / Workstation with Terminal Emulation Software Managed Switch RS232 to RJ45 Cable...
4.1 Logging on to the Console Once the terminal is connected to the device, power on the Industrial Managed PoE+ Switch and the terminal will display “running testing procedures”. Then, the following message asks to log in user name and password. The factory default user name and password are shown as follows, and the login screen in Figure 4-3 appears.
4.2 Configuring IP Address via Console The Industrial Managed PoE+ Switch is shipped with default IP address as follows: IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 To check the current IP address or modify a new IP address for the Industrial Managed PoE+ Switch, please use the procedures as follows: ...
IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.254 Figure 4-5: IP Address Screen 5. Repeat Step 1 to check if the IP address has changed. If the IP is successfully configured, the Industrial Managed PoE+ Switch will apply the new IP address setting immediately. You can access the Web interface of the Industrial Managed PoE+ Switch through the new IP address.
5. Sarting Web Management The following shows how to start up the Web Management of the Industrial Managed PoE+ Switch. Note the Industrial Managed PoE+ Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address.
Page 13
3. After entering the password, the main screen appears as Figure 5-3 shows. The following web screen is based on the IGS-4215-4P2T2S. The display of the other IGS-4215 PoE Series is the same as that of the IGS-4215-4P2T2S. Figure 5-3: Web Main Screen of Industrial Managed PoE+ Switch The Switch Menu on the left of the Web page lets you access all the commands and statistics the Industrial Managed PoE+ Switch provides Figure 5-4: Switch Menu Figure 5-5: Switch Sub-menu...
Figure 5-6: Switch Sub-menu Now, you can use the Web management interface to continue the Switch management. Please refer to the user’s manual for more. 5.2 Saving Configuration via Web To save all applied changes and set the current configuration as a startup configuration, the startup-configuration file will be loaded automatically across a system reboot.
7. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team.