Table of Contents 1. Package Contents ................. 3 2. Requirements ..................4 3. Wiring the Power Inputs ............... 5 4. Terminal Setup (IGS-4215-16T2S and IGS-4215-16T2S-U) ...... 8 4.1 Logging on to the Console .............. 9 4.2 Configuring IP Address via the Console .......... 10 4.3 Storing Current Switch Configuration ..........12 4.4 SSH Login (IGS-4215-8T2S and IGS-4215-4T2S) ......
1. Package Contents Thank you for purchasing PLANET Industrial L2/L4 Managed Gigabit Ethernet Switch, IGS-4215 series. The descriptions of these models are as follows: 10/100/1000T 100/1000X Models RJ45 Ports SFP Ports IGS-4215-4T2S IGS-4215-8T2S IGS-4215-16T2S IGS-4215-16T2S-U “Industrial Managed Switch” mentioned in this Quick Installation Guide refers to the IGS-4215 series. Open the box of the Industrial Managed Switch and carefully unpack it. The...
2. Requirements The Industrial Managed Switch provides local and remote login interface for management purposes. The following equipment is necessary for further management: z Workstations running Windows XP/2003/Vista/7/8/10/2008/10, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP proto- cols.
3. Wiring the Power Inputs The Upper Panel of the Industrial Managed Switch consists of one terminal block connector within 6 contacts for two redundant power inputs and fault alarm. Please follow the steps below to insert the power wire. 1. Insert positive/negative DC power wires into contacts 1 and 2 for Power 1 or 5 and 6 for Power 2.
Page 7
The wire gauge for the terminal block should be in the range from 12 to 24 AWG. Use one power input when using AC 24V. PWR1 and PWR2 must provide the same DC voltage while operating with dual power input.
4. Terminal Setup (IGS-4215-16T2S and IGS-4215- 16T2S-U) To configure the system in IGS-4215-16T2S, connect a serial cable to a COM port on a PC or notebook computer and to the RJ45 type serial (console) port of the Industrial Managed Switch. To configure the system in the IGS-4215-16T2S-U, connect a USB cable to a USB port on a PC or notebook computer and to the micro USB connector (console) of the Industrial Managed Switch.
1. Run terminal program on the OS. 2. When the following screen appears, make sure that the COM port should be configured as: z Baud: 115200 z Data bits: 8 z Parity: None z Stop bits:1 z Flow control: None 4.1 Logging on to the Console Once the terminal has been connected to the device, power on the Industrial Managed Switch and the terminal will display “running testing procedures”. Then, the following message asks to log in user name and password. The factory default user name and password are shown in Figure 4-2 below.
The user can now enter commands to manage the Industrial Managed Switch. For a detailed description of the commands, please refer to the following chapters. 1. For security reason, please change and memorize the new password after this first setup. 2.
Page 11
Configuration of the IP address 1. At the “IGS-4215-16T2S #” prompt, enter “configure”. 2. At the “IGS-4215-16T2S (config)#” prompt, enter the following command and press <Enter> as shown in Figure 4-4. IGS-4215-16T2S (config)# ip address 192.168.1.100 mask 255.255.255.0 IGS-4215-16T2S (config)# ip default-gateway 192.168.1.254 The previous command would apply the following settings for the Industrial Managed Switch.
4.3 Storing Current Switch Configuration 1. At the “IGS-4215-16T2S #” prompt, enter “copy running-config startup-config” as shown in Figure 4-5. Figure 4-5: Saving Current Configuration Command Screen If you are not familiar with console command or the related parameter, enter “?” anytime in console to get the help descrip- tion.
4.4 SSH Login (IGS-4215-8T2S and IGS-4215-4T2S) The IGS-4215 series also support SSHv2 for secure remote management as default. The switch asks for user name and password for remote login when using telnet; please use “admin” for both username and password. Default IP address: 192.168.0.100 Username: admin Password: admin Figure 4-6: Industrial Managed Switch SSH Login Screen The user can now enter commands to manage the Industrial Managed Switch.
5. Starting Web Management The following shows how to start up the Web Management of the Industrial Managed Switch. Note the Industrial Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address.
5.1 Logging in to the Industrial Managed Switch 1. Use Internet Explorer 8.0 or above Web browser and enter IP address https://192.168.0.100 to access the Web interface. 2. When the following dialog box appears, please enter the default user name and password “admin”. The login screen in Figure 5-2 appears. Default IP Address: 192.168.0.100 Default Username: admin Default Password: admin...
Page 16
The Switch Menu on the left of the Web page lets you access all the commands and statistics the Industrial Managed Switch provides. Figure 5-4: Switch Menu Now, you can use the Web management interface to continue the Switch management. Please refer to the user’s manual for more.
5.2. Saving Configuration via the Web To save all applied changes and set the current configuration as a startup configuration, the startup-configuration file will be loaded automatically across a system reboot. 1. Click “Save > Save Configurations to FLASH” to log in to the “Configu- ration Manager”...
6. Recovering Back to Default Configuration IP Address has been changed or admin password has been forgotten – To reset the IP address to the default IP Address “192.168.0.100” or reset the login password to default value, press the hardware reset button on the front panel for about 10 seconds. After the device is rebooted, you can log in the management Web interface within the same subnet of 192.168.0.xx.
7. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team.
Need help?
Do you have a question about the IGS-4215 Series and is the answer not in the manual?
Questions and answers