Related Manuals for Advantech POC-824
Summary of Contents for Advantech POC-824
- Page 1 User Manual POC-824 Point-of-Care Terminal with an Intel® Core™ i7/i5/i3 Processor and 23.8" TFT LCD...
- Page 2 Repair of the device may only be carried out by trained service personnel. Advantech recommends that a service contract be obtained with Advantech Service and that all repairs be carried out by them. Otherwise, the correct func- tioning of the device may be compromised.
- Page 3 The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same (CR2032) or equivalent type recommended by the manufacturer. Discard used batteries according to the manufac- turer’s instructions POC-824 Series User Manual...
- Page 4 Maintenance: to properly maintain and clean the surfaces, use only approved products or clean with a dry applicator. Caution! When servicing the device, always use replacement parts that meet Advantech standards. Advantech Medical cannot warrant or endorse the safe performance of third-party replacement parts for use with our medical devices.
- Page 5 Avoid touching the backside of the device when operating. If it is necessary, do not touch it for more than one second to avoid risk of injury. If there is a need to touch the backside for cleaning, turn off the device first. POC-824 Series User Manual...
- Page 6 The symbol on electrical and electronic products only applies to the current European Union Member States. POC-824 Series User Manual...
- Page 7 It is strongly recommended that only these accessories be used in conjunction with the device. Otherwise, the correct functioning of the device may be compromised. POC-824 Series User Manual...
- Page 8 Additional Information and Assistance Contact your distributor, sales representative, or Advantech's customer service cen- ter for technical support if you need additional assistance. Please have the following information ready before you call: Product name and serial number Description of your peripheral attachments ...
- Page 9 évitée, peut entra?ner des blessures mineures ou modérées à l'utilisateur ou au patient ou des dommages à l'équipement ou à d'autres biens. Remarque! Une REMARQUE fournit des informations supplémentaires destinées à éviter les inconvénients en cours de fonctionnement. POC-824 Series User Manual...
- Page 10 La réparation de l'appareil ne doit être effectuée que par du personnel de ser- vice qualifié. Advantech recommande qu'un contrat de service soit conclu avec le service de maintenance Advantech et que toutes les réparations soient également effectuées par ce dernier. Sinon, le bon fonctionnement de l'appareil pourrait être compromis.
- Page 11 Mise en garde! Lors de l'entretien de l'appareil, utilisez toujours des pièces de rechange conformes aux normes Advantech. Advantech Digital Healthcare ne peut en aucun cas garantir ou garantir la sécurité des pièces de rechange tierces à utiliser avec notre dispositif médical.
- Page 12 UL/CSA, 18 AWG min., 3 m max., qualité hospitalière si pour le marché américain/canadien. L'appareil est uniquement destiné à être maintenu debout lors de son fonctionnement. Ne posez aucun côté du panneau LCD ou l'arrière à plat sur une surface quelconque lors de l'utilisation. POC-824 Series User Manual...
- Page 13 Ne touchez pas l'arrière de l'appareil lors de son fonctionnement. S'il est néces- saire de toucher le dos, ne touchez pas plus d'une seconde pour éviter tout ris- que de blessure. S'il est nécessaire de toucher l'arrière pour le nettoyer, éteignez d'abord l'appareil. xiii POC-824 Series User Manual...
- Page 14 POC-824 Series User Manual...
-
Page 15: Table Of Contents
Specifications .................... 2 Table 1.1: Specifications ............. 2 Dimensions ....................4 Figure 1.1 Dimensions of the POC-824........4 Figure 1.2 VESA Mounting of the POC-824 ........ 5 Figure 1.3 POC-824 Series Bottom Panel........5 1.3.1 Optional modules ................6 1.3.2 Cleaning and disinfecting.............. - Page 16 POC-824 Series User Manual...
-
Page 17: Chapter 1 General Information
Chapter General Information... -
Page 18: Introduction
Introduction The POC-824 is a multimedia Intel® Core™ i7 or i5 processor device designed for mobile computing as a Point-of-Care terminal (POC-824.) It is a PC-based system with a 23.8" wide TFT LCD display with HDMI and triple LAN connectivity. It has dual COM ports (RS232), 4 x USB 2.0 ports, and a 24-bit stereo audio controller. - Page 19 2.5" SSD 128/ 256G/ 512GB/ 1TB or 2TB Optional Configuration WLAN Intel® Wireless-AC9260 or Intel® AX210 Bluetooth 5.1 (Intel® 9260) / 5.2 (Intel® AX210) RFIDEAS OEM-805N24KU-X RFID (Dual-band card reader supports RFID frequency of 125kHz and 13.56MHz) POC-824 Series User Manual...
-
Page 20: Dimensions
Dimensions Dimensions: 583.38 x 386.74 x 59.95 mm (Unit: mm) Figure 1.1 Dimensions of the POC-824 VESA Mounting: 75 x 75 mm; 100 x 100 mm Note! For VESA mounting, please see the installation steps in Appendix A. POC-824 Series User Manual... - Page 21 Figure 1.2 VESA Mounting of the POC-824 Warning! Use suitable mounting apparatus to avoid risk of injury. Attention! Utilisez un appareil de montage approprié pour éviter tout risque de blessure. Figure 1.3 POC-824 Series Bottom Panel Equipotential Terminal Pin 2 x COM ports (RS232)
-
Page 22: Optional Modules
During normal use of the POC (Point-of-Care Terminal) the device may become dirty and should be regularly cleaned. Steps: Prepare cleaning water. Wipe the POC-824 with a clean cloth that has been moistened in the cleaning solution. Wipe thoroughly with a clean dry cloth. Caution! Do not immerse or rinse the POC-824 or its peripherals. -
Page 23: Intended User Profile
– One arm/hand capable of guiding and holding the device – An average degree of aging-related short term memory impairment – Hearing impairment of 40%, resulting in 60% of normal hearing at 500 Hz to 2 POC-824 Series User Manual... - Page 24 POC-824 Series User Manual...
-
Page 25: Chapter 2 System Setup
Chapter System Setup... -
Page 26: A Quick Tour Of The Poc-824
A Quick Tour of the POC-824 Before you start to set up the POC-824, take a moment to become familiar with the locations and functions of the controls, drives, connections, and ports, which are illus- trated in the figures below. -
Page 27: Rear View
Figure 2.3 Bottom Panel with the Various I/O Ports 1. Equipotential Terminal Pin 2. 2 x COM ports (RS232) 3. Power button 4. Line-Out 5. Mic-In 6. 3 x LAN ports 7. 4 x USB 3.0 8. DisplayPort 9. HDMI 10. DC-In POC-824 Series User Manual... -
Page 28: Installation Procedures
Installation Procedures 2.2.1 Connecting the power cord The POC-824 SERIES can only be powered by DC adapters as follows. Adapter Technology / ATM250T-A120, 100-240 Vac, 50-60 Hz, 3.3-1.3A or Adapter Technology / ATM300T-A120, 100-240 Vac, 50-60 Hz, 3.5-1.5A or Adapter Technology / ATM250T-P120, 100-240 Vac, 50-60 Hz, 3.3-1.3A When using ATM250T-A120 or ATM300T-A120, be sure to always handle the power cords by holding the plug ends only. -
Page 29: Connecting The Dc-In
Caution! The adapter DC-In plug must be properly and tightly connected to the POC System (as shown below) without any gap in between. Proper DC-In connection without a gap Improper DC-In connection with a gap Warning! An improper DC-In connection may damage the POC system or adapter. POC-824 Series User Manual... -
Page 30: Connecting The Ground Pin
10. DC-In Connect the grounding cable and the terminal link to the hospital grounding/ earthing system. Figure 2.6 Grounding Cable with Connector Connect the grounding cable plug to the POC-824 SERIES Equipotential Termi- nal (See Figure 2.6). POC-824 Series User Manual... -
Page 31: Running The Bios Setup Program
Running the BIOS Setup Program Your POC-824 was probably set up and configured by your dealer prior to delivery. You may still find it necessary to use the BIOS (Basic Input-Output System) setup program to change system configuration information, such as the current date and time or your type of hard drive. -
Page 32: Installing The Drivers
Ethernet, audio, and touchscreen functions from your own external CD-ROM drive. All the drivers, except the CD-ROM drive driver, are available from the download link on the Advantech website. If you have any questions, please contact the Advantech AE team for further support. -
Page 33: Emc Declaration
Guidance and manufacturer’s declaration – electromagnetic emissions The POC-824 is intended for use in the electromagnetic environment specified below. The customer or the user of the POC-824 should assure that it is used in such an environment. Electromagnetic Environment– Emissions Test... - Page 34 Guidance and manufacturer’s declaration – electromagnetic immunity The POC-824 is intended for use in the electromagnetic environment specified below. The customer or the user of the POC-824 should assure that it is used in such an environment. IEC 60601 test...
- Page 35 Guidance and manufacturer’s declaration – electromagnetic immunity The POC-824 is intended for use in the electromagnetic environment specified below. The customer or the user of the POC-824 should assure that it is used in such an environment. Immunity IEC 60601 test Compliance Electromagnetic environment –...
- Page 36 RF transmitters, an electromagnetic site survey should be consid- ered. If the measured field strength in the location in which the POC-824 is used exceeds the applicable RF compliance level above, the POC-824 should be observed to verify nor- mal operation.
-
Page 37: Chapter 3 Operation And Safety
Chapter Operation and Safety... -
Page 38: General Safety Guide
Thermal The vent hole of the POC-824 rear cover functions as a cooling airflow inlet and out- let. These air inlets and outlets transfer heat from inside the computer to the cooler air outside. Do not block these holes/vents with any soft material. -
Page 39: Disconnecting The Power
Never place anything on the system case before turning off the com- puter. Never turn on your computer unless all of its internal and external parts are in place. Operating the computer when it is open or with parts missing can be dangerous and may cause damage. POC-824 Series User Manual... - Page 40 POC-824 Series User Manual...
-
Page 41: Appendix A Installing A Vesa Mount
Appendix Installing a VESA Mount... -
Page 42: Installing A Vesa Mount
Please contact a service technician or your retailer if you need this service. Installation instructions: First attach the wall-mount to the back cover of the POC-824, then secure it in place with the four Phillips-head screws provided. Note! Please use M4x8L (Maximum) screws and use 4 screws for VESA mounting. - Page 43 Figure A.1 VESA Mounting POC-824 Series User Manual...
- Page 44 POC-824 Series User Manual...
-
Page 45: Appendix B Driver Installation
Appendix Driver Installation... -
Page 46: Driver Installation
Driver installation The POC-824 supports Windows WIN10 IOT/RS5 versions or later, 64-bit only. There is no longer support for 32-bit drivers. Warning! Please use a clean OS installation before installing the drivers; other- wise, unexpected errors may occur. Attention! Veuillez utiliser un système d'exploitation propre pour installer le pilote, sinon cela pourrait provoquer une erreur inattendue. - Page 47 POC-824 Series User Manual...
- Page 48 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2023...
Need help?
Do you have a question about the POC-824 and is the answer not in the manual?
Questions and answers