Clarion VRX8271 Owner's Manual And Installation Manual page 26

3) Press one of the Preset buttons LfLi (No. 1 to
No. 6) and select the DSP menu to be set.
<DSP BASIC1> (for DPH9100/DPH7100)
No.l HAL(HALL) Sound setting simulating
a large hall
No.2 CHC(CHURCH)
Sound setting simulating
a big church with a very
high ceiling
No.3 SDM(STADIUM)
Sound setting simulating
a large stadium with no
fence or ceiling
No.4 LVH(LIVE HOUSE)
Sound setting simulating
a live house slightly
larger than a jazz club
No.5 DIS(DISCO)
Sound setting simulating
a disco where the bass
is emphasized
No.6 JAZ(JAZZ CLUB)
Sound setting simulating
a jazz club with a low
ceiling
<DSP BASIC2> (only for DPH9100)
No.l DOM(DOME) Sound setting simulating
an indoor sports ground
No.2 CHM(CHAMBER) Sound setting simulating
a grand chamber of a
court
No.3 PRK(PARK) Sound setting simulating
a large outdoor field
No.4 THE(THEATER)
Sound setting simulating
a movie house or
theater
No.5 STU(STUDIO) Sound setting simulating
a listening room
No.6 BGM(BGM)
Vocal sound is
eliminated.
<DSP USER> (only for DPH9100)
No.l US1 (DSP U-1)
Set by the user.
No.2 US2(DSP U-2)
Set by the user.
No.3 US3(DSP U-3)
Set by the user.
No.4 US4(DSP U-4)
Set by the user.
No.5 US5(DSP U-5)
Set by the user.
No.6 US6(DSP U-6)
Set by the user.
Note:
•
Turn on the DSP effect after following instructions
in the next subsection, "Turning on and off the
DSP effect." Otherwise, the above settings will be
invalidated.
Turning on and off the DSP effect
1) Press the ADJ button jl5j and go to the CON¬
FIGURATION mode.
2) Slide the Up/Down button [T] to ▼ (down) or
▲ (up) to move the cursor to "DSP".
3) Slide the Up/Down button (Tj to ► (right) to
turn "OFF" and "ON".
4) Press the ADJ button 511 and return to the
previous mode.
Setting your own DSP characteris¬
tics
Up to 6 DSP characteristics can be set by the user
and stored in the DSP USER (US-1 to US-6).
Notes:
•
This function is available only when the DPH9100
(sold separately) is connected to the source unit.
• If the control is idle for about 5 seconds after each
operation, the unit returns to the previous mode.
• If DSP is turned off in the CONFIGURATION
mode, the following instructions cannot be operat¬
ed.
1) Press the DSP button QH to go to the DSP
mode.
2) Press the BAND button [|] to select DSP
USER.
3) Press the ADJ button SU when DSP USER is
displayed to select the adjustment menu.
4) Press ►/» (center) of the ENT button [T] to
go to the "DSP EDIT" adjustment mode.
Adjustment items are displayed as shown on
the next page.
To move the cursor to the next item, slide the
Up/Down button i to ► (right) and to move
it to the previous item, slide the button to -4
(left). (If you slide and hold the Up/Down but¬
ton Li] to -4 (left), the adjustment menu
returns.) (*1 in the table on the next page)
Slide the Up/Down button [Tj to ▲ (up) and
▼ (down) to change each set value (*2 in
the table on the next page).
Note:
•
The sound setting menu "DSP BASIC1" has
already been set in DSP USER.
27