OBH Nordica Perfect Mix+ LH871DS0 Instructions For Use Manual page 33

• Fill up the jug with 1 litre of hot water along with 2 or 3 drops of
washing up liquid. Only use the recommended amount of water
and washing up liquid. An excess of washing up liquid creates
more foam and consequently can lead to overflowing.
• Use the automatic auto clean program to carry out a prewash of the jug.
• Once the program has stopped, unplug the appliance.
• Remove the blender jug (F4, O4)
• Place the jug on a flat surface.
• Unlock the lid and remove it with care. Pour out the water.
• Remove the Blade Unit + Locking Ring + Seal (F1 + F2 + F3 / O1 + O2
+O3) and clean them under running water. The blades are very sharp,
handle them with caution to avoid injury (Fig. 10).
18
• After cleaning, remember to correctly fit the seal (F3, O3) back onto
the blade unit (F1, O1) (Fig. 17). Please be careful to avoid any damage
to the seal by touching the blades.
Note: Incorrectly fitting the seal can result in ingredients leaking from
the base of the blender jug.
• Rinse the inside of the jug and the lid under running water.
• Take care when cleaning the blades in the blender jug and when you
empty the jug as they are sharp.
• Use a damp cloth to clean the motor unit (A). Dry it carefully.
• The detachable parts (lid, blade unit, locking ring,) can be cleaned
with a sponge and hot soapy water.
• The jug (F4, O4), blade unit without titanium coating (F1), locking ring
(F2, O2) can be cleaned in the dishwasher on the upper rack - use the
'ECO' or 'LOW SALT' program.
• Caution: The jug (F4, O4), blade unit without titanium coating (F1) and
locking ring (F2, O2) must be disassembled and placed separately in
the dishwasher. Please do not put the blades with titanium coating
(O1) in the dishwasher.
64
19
WHAT TO DO IF YOUR APPLIANCE DOES NOT WORK
PROBLEMS CAUSES
The plug is not
connected
Appliance does not work
The blender jug is not
positioned correctly on
the motor unit
The appliance stopped
Overload
while in use
The product is not placed
on a flat, stable surface
Excessive vibrations
Volume of ingredients is
too high
Volume of ingredients is
too high
Leak from the lid
The lid is not correctly
positioned
The blender seal (F3 /
Leak at the bottom of the
O3) is not positioned
blender jug
correctly or is absent
Pieces of food are too
large or too hard. Liquid
The blade does not turn
has been blended that
easily
was too hot and has
distorted the seal
YOUR APPLIANCE STILL DOES NOT WORK?
Contact an approved service centre (see list in service booklet).
SOLUTIONS
Connect the appliance
to a socket with the
same voltage as that on
the rating plate of the
appliance.
Check that the blender
jug is positioned
properly on the motor
unit as explained in the
instructions.
Follow the instructions
in section USING YOUR
BLENDER.
The cooling time is
variable and can last up
to 30 minutes
Place the appliance on
a flat surface.
Reduce the quantity of
ingredients processed.
Reduce the quantity of
ingredients processed.
Place the lid correctly on
the blender jug.
Reposition the seal
with the correct side
uppermost (Fig. 1) and
lock the assembled blade
unit (F1+F2+F3 / O1 + O2
+O3) onto the blender jug
correctly (Fig. 2, Fig. 3 & Fig.
4 / Fig. 9, Fig. 10 & Fig. 11)
Replace the seal with a
new one. Reduce the size
or quantity of ingredients
processed. Add liquid.
65