Advertisement
Quick Links
Series:
3SEC-A
2HP, 3450 RPM, 60 HZ
4SEC-A
3 & 5 HP, 1750 RPM, 60 HZ
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notification.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
INSTALLATION MANUAL
Submersible Cutter Pump
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
Form No. 148427 rev. B
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Crane BARNES 3SEC-A Series
Summary of Contents for Crane BARNES 3SEC-A Series
- Page 1 Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur. As such Crane Pumps & Systems reserves the right to change product without prior written notification. A Crane Co. Company...
-
Page 2: Safety First
Other brand and product names are trademarks or registered trademarks of their respective holders. ® Barnes is a registered trademark of Crane Pumps & Systems Inc. 4/07 Alteration Rights Reserved... - Page 3 USER GUIDE USER GUIDE For future reference, record the following Congratulations on your purchase of a Barnes information: SEC Cutter pump system. With proper care and by Station Serial No: following a few simple guidelines your cutter pump will give you many years of dependable service. Pump Model No: Use and Care Pump Serial No:...
- Page 4 3SEC20_2A SPECIFICATIONS: DISCHARGE ....... JIS 80 Horizontal Flange UPPER BEARING: LIQUID TEMPERATURE ..104°F (40°C) Continuous Design: Single Row, Ball, MOTOR HOUSING ..... Cast Iron A-48, Class 30 Shielded and Permanently Lubricated VOLUTE ......Cast Iron A-48, Class 30 LOWER BEARING ..........
- Page 5 4SEC30_4A SPECIFICATIONS: DISCHARGE ....... JIS 80 Horizontal Flange UPPER BEARING: LIQUID TEMPERATURE ..104°F (40°C) Continuous Design: Single Row, Ball, MOTOR HOUSING ..... Cast Iron A-48, Class 30 Shielded and Permanently Lubricated VOLUTE ......Cast Iron A-48, Class 30 LOWER BEARING ..........
- Page 6 4SEC30_4A HORIZONTAL ADAPTER:...
- Page 7 4SEC50_4A SPECIFICATIONS: DISCHARGE ....... JIS 80 Horizontal Flange UPPER BEARING: LIQUID TEMPERATURE ..104°F (40°C) Continuous Design: Single Row, Ball, MOTOR HOUSING ..... Cast Iron A-48, Class 30 Shielded and Permanently Lubricated VOLUTE ......Cast Iron A-48, Class 30 LOWER BEARING ..........
- Page 8 4SEC50_4A WITH HORIZONTAL ADAPTER:...
- Page 9 For the location of the nearest Barnes Service Center, check your rails into place on the discharge base elbow. Once the rails are in Barnes representative or Crane Pumps & Systems, Inc. proper alignment, bolt the base elbow into the floor of the station Service Department in Piqua, Ohio, telephone and connect the discharge pipe to the elbow.
-
Page 10: Electrical Connections
ELECTRICAL CONNECTIONS: WARNING! - All model pumps and control panels must be properly grounded per the NATIONAL ELECTRIC CODE or CANADIAN ELECTRIC CODE, State, Province and local codes. Improper grounding voids warranty. Pump Cables - The cord assembly mounted to the pump must NOT be modified in any way except for shortening to a specific application. - Page 11 WIRING DIAGRAM 2HP, 3HP, & 5HP...
-
Page 12: Troubleshooting
TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... - Page 13 Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”. CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR. Products Returned Must Be Cleaned, Sanitized, Or Decontaminated As Necessary Prior To Shipment, To Insure That Employees Will Not Be Exposed To Health Hazards In Handling Said Material.
- Page 14 Notes...
Need help?
Do you have a question about the BARNES 3SEC-A Series and is the answer not in the manual?
Questions and answers