protech prox IV-Z318 Quick Reference Manual

IV-Z318
Quick
Reference
Guide

Jumper Settings

Clear ME RTC Register and
CMOS Selection
1 1
Normal
Clear CMOS
(default)
1
Clear ME
RTC Register
CAUTION!
Danger of explosion may occur if the battery is replaced incorrectly.Replace batteries only with the same or equivalent type recommended by the manufacturer.
Dispose the used batteries according to the manufacturer's instructions.
Ver. Q3
All Rights Reserved. Copyright 2022
1 1 1 1
JLED_WLAN2 JLED_WWAN1 JLED_HDD1 JSYS_LED1
1
1
PWRBTN1
JBAT1
1
7 1 7
1
1 SATA1 SATA2
JSATA_PWR1
JLOWBATDET
PWRBTN2
DIMM1
1
2
1
JCMOS_RTC1
12 11
2 1
6
1
JUSB1
1 6
5 1
5 1
10
6 6
5 10
10
JCOM3 JCOM4
1 6
JAUDIO1
5 1
5 10 10 6
USB1 USB2

Specification

System
CPU Support
Memory Support
Graphics
Watchdog
Power Input
Expansion Slots
TPM
Mounting Support
Operating System
Dimensions & Weight
Certifications
I/O Ports
Drive Bay
USB
LAN
Serial Ports
Display
Audio
Digital I/O
SIM Card Sockets
Antenna Holes
LED
Power On / Off
Ground
Environment
Operating Temp.
Storage Temp.
Vibration (Random)
Vibration (Operating)
Vibration (Storage)
Shock (Operating)
Shock (Non-Operating)
DP1 HDMI1
1
JSATA_PWR2
SP1
57 67 75
58 68
74
M2_PCIE1
75
1
M_PCIE2
M2_E1
75 74
M5
33 32
23 22
1 2
M6
10
5
RJ45_LAN1 RJ45_LAN2 RJ45_LAN3 RJ45_LAN4
®
Intel 11th Gen. Core™ i7 / i5 / i3 processor
2 x DDR4-3200 SO-DIMM up to 32 GB
® ®
Intel Iris Xe Graphics (for i7 and i5) / Intel
1~255 seconds watchdog timer selectable
DC In 9~48V (with ignition)
1 x full-sized Mini PCIe slot 1
(USB2.0 and SIM signal)
1 x full-sized Mini PCIe slot 2
(PCIe and USB 2.0 signal)
1 x M.2 3042/3052-D2-B slot (
PCIe,USB 3.0 and USB 2.0 and SIM signal)
1 x M.2 2230-D2-E slot
(PCIe and USB 2.0 signal)
1 x M.2 2280-D2-M slot
(PCIe Gen4 x 4 signal)
TPM 2.0
Wall Mount (default) / VESA Mount (75x75) / DIN Rail (optional)
Windows 10 LTSC 2019/2021 / Windows 11 IoT Enterprise (GAC) /
Ubuntu 20.04 LTS
259.5 x 72 x 184.8mm ((WxHxD) / 3.2kg
FCC / CE / E13
2 x 2.5" SATA SSD (Support RAID 0/1)
2 x USB 3.2 Gen 2 and 2 x USB 2.0
4 x RJ45 / M12-X-coded GbE with optional PoE (IEEE 802.3af)
Supports Wake-On-LAN/PXE
COM 1/2 for RS-232/422/485 with 3KVrms isolation
COM 3/4 for RS-232 (optional with CAN Bus)
2 x HDMI 2.0: Max. resolution 4K @ 60Hz
1 x DP1.4: Max. resolution 4K @ 60Hz
1 x Line Out, 1 x Mic In
4 x in / 4 x out with 3KVrms isolation
2 x Nano SIM card slots
7 x Antenna holes
1 x System LED, 1 x HDD LED, 1 x WWAN LED, 1 x WLAN LED,
4 x PoE LED
1 x Power Button / 1 x Reset Button / 1 x Remote Switch
1 x M3 hole
-40°C~70°C (32°F~158°F) (with ambient airflow)
-40°C~85°C (-4°F~185°F) / Humidity: 20%~ 90%
IEC60068-2-64, random, 2.5G@5~500Hz, 1hr/axis with SSD
MIL-STD-810G, 514.6C Procedure 1, Category 4
MIL-STD-810G, 514.6E Procedure 1, Category 24
MIL-STD-810G, 516.6 Procedure I, trucks and semi-trailers=40G
MIL-STD-810G, 516.6,Procedure V, crash hazard shock test=100G
52 51
18
16 15
2 1
M1
M_PCIE1
74
M3
M2_B1
M2
2
NOTES
1. In order to have ignition power control
for in-vehicle usage, you need to supply
M4 M4
IGN signal to the system before enabling
"Power On/Off Function" in BIOS.
2. How to set up Power Cable for Ignition
4 1
1 2
J12VOUT1
Function:
The power terminal block connector of
IV-Z318 has 3 pins: GND/ VCC/ Ignition.
19 20
When using power from battery, Ignition has
to be in contact with the VCC pin. Or you
can simulate vehicle engine start, and then
the ignition pin can connect a switch to start
the system.
JDC_IN1
IV-Z318
®
UHD Graphics (for i3)
IV-Z318