Advertisement
SJ3A6
VVacuum release valve manifold with restrictor
SS3J3
q
Vacuum release valve
with restrictor type
w
Cable type
t
Connector entry
With parallel wiring specifications,
it is necessary to select the con-
nector entry direction (1: upward,
2: lateral). For details, refer to
page 33.
i
SUP/EXH block fitting specification
Nil
Straight fitting
X, PE port:
Elbow fitting
∗ There is no need to enter anything when the SUP/EXH block mounting position "M" is selected. Also, this manifold comes
standard with external pilot specifications.
How to Order Manifold Assembly
SS3J3-V60LPD2-
Ordering example (
With plug (24 VDC)
SJ3A6-5FZ-P (2 sets)
129
Plug-in
Cable Type
Vacuum Release Valve with Restrictor
How to Order
V
60
L
q
w
e
Connector type
Symbol
Mounting position
F
D-sub connector
P
Flat ribbon cable with 26 pins
PG
Flat ribbon cable with 20 pins
PH
Flat ribbon cable with 10 pins
y
Valve stations
F
: D-sub connector
Symbol
Stations
02
2 stations
10
10 stations
PG
: Flat ribbon cable (20 pins)
Symbol
Stations
02
2 stations
09
9 stations
∗ This number also includes the blanking block.
∗ The cable type is only applicable when there are 2 or more stations.
L
Elbow fitting
(Upward)
X, PE port:
Straight fitting
m)
With plug (24 VDC)
SJ3A6-5FZ-DP (4 sets)
SUP/EXH block (D side mounting)
Series
An order cannot be placed with only the manifold part
no. Be sure to order solenoid valves for mounting at
the same time while referring to the ordering example.
D
05
U
e r t
y
u i o
Page
Note
33
Parallel wiring
P
: Flat ribbon cable (26 pins)
Symbol
Stations
02
2 stations
10
10 stations
PH
: Flat ribbon cable (10 pins)
Symbol
Stations
02
2 stations
04
4 stations
B
Elbow fitting
(Downward)
X, PE port:
Elbow fitting
SS3J3-V60LPD2-06D ············1 set (Manifold part no.)
∗ SJ3A6-5FZ-DP ························4 sets (With plug part no.)
∗ SJ3A6-5FZ-P ···························2 sets (With plug part no.)
The asterisk denotes the symbol for the assembly.
Prefix it to the part numbers of the solenoid valves, etc.
· For the valve arrangement, the valve closest to the D side is
considered the 1st station.
· Under the manifold part number, state the valves to be mounted in
order starting with the 1st station as shown in the figure. If the
arrangement becomes too complicated, specify the details on a
manifold specification sheet.
®
RoHS
r
Connector mounting
position
Symbol
Mounting position
D
D side
u
SUP/EXH block
mounting position
U
U side
D
D side
B
Both sides
∗
M
1
Special specifications
∗1 For the special specifications, a
port size of the SUP/EXH block
can be specified. At this time,
the mounting position becomes
only U, D, or B.
o
DIN rail length
specified
Nil
Standard length
3
3 stations Specify a length
longer than that of
10
the standard rail.
10 stations
∗ When specifying a length longer
than that of the standard rail, se-
lect the number of valve stations
without exceeding the max. num-
ber of stations.
Advertisement
