CYBEX Cloud G i-Size User Manual page 12

4. Push the ISOFIX-Locking arms (6) out of the Base G to their furthest
extent.
EN
5. Place the Base (7) on an appropriate seat in the vehicle.
6. Push the ISOFIX-Locking arms (6) into the ISOFIX-Anchorage points
(8) until these lock into place with an audible "CLICK". The two ISOFIX-
Indicators (9) will switch from RED to GREEN.
7. Ensure the Base (7) is secure by trying to pull it out of the ISOFIX-
Anchorage points (8).
8. Push the Base (7) towards the backrest of the vehicle seat until it is fully
aligned with the backrest.
�� Moving the base from side to side will also brace it against the vehicle
backrest.
9. Press the Load leg adjustment button (10) and extend the leg until it
touches the vehicle floor.
10. Pull the Load leg (4) out to the next locking position to ensure optimal force
transmission.
11. The Load leg indicator (11) switches to GREEN when the load leg is
correctly positioned on the vehicle floor.
12. Move the Carrying handle (12) to position A. Therefor, press the two
Carrying Handle release buttons (13) on the left and right of the Carrying
Handle at the same time.
13. Place the car seat on the Base (7).
14. The car seat can also be placed in its entry position on the base. Then turn
the car seat until it is aligned opposite to the direction of travel.
15. Please ensure that the car seat locks into place with an audible "CLICK".
16. Check whether the Seat locking indicator (14) on the base is GREEN.
Installing the car seat with 3-point automatic belt
1. Place the car seat on the vehicle seat against the direction of travel.
2. Make sure that the Carrying handle (12) is locked in position A.
3. Make sure that the Tilt angle indicator (15) is parallel with the vehicle floor.
4. Pull out the 3-point automatic belt (16) and place its lap section into the lap
belt guide (17).
5. Lock the 3-point automatic belt (16) of the vehicle in its belt buckle.
6. Tighten the lap section by pulling the diagonal section in the direction of
travel.
8
7. Guide the diagonal section of the belt behind the head end of the car seat
and through the Diagonal belt guide (18) and above the Linear side-impact
protection (L.S.P) (19).
REMOVAL FROM THE VEHICLE
Removal of the car seat with Base G
1. To unlock the car seat from the Base (7), pull one of the Seat release
handles (20)/(21) up.
2. Tilt the car seat slightly and lift it off the Base (7).
3. Unlock the ISOFIX-Locking arms (6) on both sides by pressing the ISOFIX-
Release buttons (5) and at the same time pulling them back.
4. Pull out the Base (7) from the ISOFIX-Anchorage points (8).
5. Remove the Base (7) and slide the ISOFIX-Locking arms (6) completely
back into their transport positions.
6. Push the Load leg (4) back into its original position and then fold it in to
save space. There is a Load leg parking position (22) indicated on the
underside of the base.
Removal of the car seat with 3-point automatic belt
1. Take the diagonal section of the belt out of the Diagonal belt guide (18).
2. Unlock the vehicle seat belt buckle and take the lap section of the belt out
from the Lap belt guides (17).
ADJUSTING THE HEADREST
The adjustable Headrest (23) can be adjusted by using the Headrest
adjustment handle (24). When adjusting the headrest ensure that the Shoulder
harness outlets (25) are at shoulder level or slightly below.
SECURING THE CHILD
1. Press the Belt adjustment button (26) and pull both Shoulder belts (27) at
the same time to loosen them.
2. Undo the Belt buckle (2) by pressing the red button firmly.
3. Put your child in the car seat with the buttocks at the back.
4. Place the Shoulder belts (27) directly over your child's shoulders.
5. Place both Buckle tongues (28) together and lock them in place in the Belt
buckle (2). You should hear an audible "CLICK".
6. If you are using a seat with a SensorSafe Clip, push the clip closed until
you hear an audible "CLICK" and slide the closed clip down towards the
Belt buckle (2).