Disable Feature; Accessing The Programming Mode - Viking E-1600A-TP-EWP Technical Practice

D. Disable Feature
The "Disable" input can be connected to a switch for remotely disabling/turning off the strobe light and the device con-
trolled by the auxiliary contacts (camera, etc.).
A. Accessing the Programming Mode
The 1600A Series emergency phones can be programmed from any Touch Tone
phone using a C.O. line, analog PABX/KSU station, or a DLE-200B Line Simulator.
1. Using the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls, see section J).
Step 2. From a Touch Tone phone call the line attached to the 1600A Series phone.
Step 3. When the 1600A Series phone answers, enter the 6-digit security code (factory set to 845464, see section C). A
double beep should then be heard indicating you have entered the programming mode.
2. Without the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls, see section J).
Step 2. Move DIP switch 3 to the OFF position (incoming calls enter Programming without security code, see section J).
Step 3. From a Touch Tone phone call the line attached to the 1600A Series phone.
Step 4. When the 1600A Series answers, a double beep will be heard and will automatically enter the programming mode.
Step 5. When finished programming, move DIP switch 3 back to the ON position (see section J).
B. Quick Programming Features
First emergency speed dial number .........................................................................
Second emergency speed dial number ...................................................................
Third emergency speed dial number .......................................................................
Fourth emergency speed dial number .....................................................................
Fifth emergency speed dial number .........................................................................
Central station receiver number ...............................................................................
Central station voice number ...................................................................................
First "Info" speed dial number (E-1600A-TP2-EWP only) ........................................
Second "Info" speed dial number (E-1600A-TP2-EWP only) ...................................
Third "Info" speed dial number (E-1600A-TP2-EWP only) .......................................
Voice announcer/miscellaneous options (factory set to 000210) .............................
Timing/Dialing options (factory set to 234111) .........................................................
Security code (factory set to 845464) ......................................................................
Identification number (factory cleared) ....................................................................
Second central station identification number (factory cleared) .................................
,
To add a at any point in the dialing string ..............................................................
To add a # at any point in the dialing string ..............................................................
To add a four second pause at any point in the dialing string ...................................
To switch to pulse dialing at any point in the dialing string ........................................
To clear any speed dial number ...............................................................................
Diagnostic tones (used to check mic and speaker operation) ..................................
Exit programming and disconnect ...........................................................................
Reset all programming to factory default settings ....................................................
A double beep indicates a valid memory position, four beeps indicate an error.
C. Security Code
(memory location #19)
The security code allows the user/installer to program the 1600A series phone while DIP switch 3 is in the ON (normal)
position. The factory set security code is 845464 (V-I-K-I-N-G). It is recommended that the factory set security code
be changed. Example: To store 123456 as the security code:
Step 1. Access programming as shown is Programming section A.
Step 2. Enter 123456 #19..
Step 3. Hang-up.
The security code must be 6 digits and cannot include a , or a .
4
?
Call (715) 386-4345 and select 605.
Enter Digits - then - Enter Memory Location
0-20 digits then
0-20 digits then
0-20 digits then
0-20 digits
then
0-20 digits then
0-20 digits then
0-20 digits then
0-20 digits then
0-20 digits
then
0-20 digits then
6 digits then
6 digits then
6 digits then
0-20 digits
then
0-20 digits then
,,
,
#
,
7
,
6
then
(no digits)
,
0
#7
###
Enter Your Security Code Here:
#00
#01
#02
#03
#04
#05
#06
#07
#08
#09
#17
#18
#19
#20
#21
#00 - #09
#19