Table of Contents
Advertisement
Quick Links
Anchor 7000
Installation Manual
Installation and Commissioning Manual
Note:
The cover sheet provides warning information, and an explanation of the symbols and terms
used, together with our disclaimer.
Mount the keypad before installing the electronic lock. For information on how to install the
keypads, please refer to "APxxxx Part 2a- Keypad Installation Manual".
Contents
General ................................................................................................................................. 2
Preparation for installation ..................................................................................................... 3
Installation dimensions of lock A7000 ................................................................................ 3
Preparation of the boltwork / door ...................................................................................... 4
Installation ............................................................................................................................. 4
Cabling / installation .............................................................................................................. 4
Cabling .............................................................................................................................. 4
Connection of an analogue keypad ................................................................................... 6
UART connection .............................................................................................................. 6
Connection of alarm contacts ............................................................................................ 7
Connecting an alarm system outside the scope of the VdS ........................................... 7
Connecting an alarm system within the scope of the VdS .............................................. 9
Functional test ......................................................................................................................10
Input of the opening code .................................................................................................10
Keypad test ......................................................................................................................10
Figure 1 - Dimensional drawing ............................................................................................. 3
Figure 2 - Drilling positions for the Primor FS ........................................................................ 5
Figure 3 - Cable connection .................................................................................................. 6
Figure 4 - Assignment of the alarm interface ......................................................................... 8
Figure 5 - Connection of the Gator Signal plus ...................................................................... 9
02 A7000-Part 2b-Installation Manual V1.04
1 / 10
Advertisement
Table of Contents
Related Manuals for Wittkopp Anchor 7000
Summary of Contents for Wittkopp Anchor 7000
-
Page 1: Table Of Contents
Anchor 7000 Installation Manual Installation and Commissioning Manual Note: The cover sheet provides warning information, and an explanation of the symbols and terms used, together with our disclaimer. Mount the keypad before installing the electronic lock. For information on how to install the keypads, please refer to “APxxxx Part 2a- Keypad Installation Manual”. -
Page 2: General
Anchor 7000 Installation Manual Installation and Commissioning Manual General A7000 series locks have standard No not allow the opening for the keyhole to installation dimensions and can be installed exceed a rectangle measuring 27 x 9 mm. in all 4 installation positions (right, left, top, bottom). -
Page 3: Preparation For Installation
Anchor 7000 Installation Manual Installation and Commissioning Manual Always adhere to the following sequence for installation: •Check the preconditions for installation •Wiring / installation of the cables •Disconnection of the power supply •Functional test of the locking mechanism •Perform all settings (user installation, time delay) -
Page 4: Preparation Of The Boltwork / Door
Anchor 7000 Installation Manual Installation and Commissioning Manual Preparation of the boltwork / door To install the lock, there needs to be three strength class 8.8) to fix the electronic lock. threaded fixing holes on the boltwork or Measure the length of the screws to ensure inside the safe door. - Page 5 Anchor 7000 Installation Manual Installation and Commissioning Manual Figure 2 - Drilling positions for the Primor FS Always route the cables in such a way that is no continuous movement of the cables they do not come into contact with moving during operation.
-
Page 6: Connection Of An Analogue Keypad
Anchor 7000 Installation Manual Installation and Commissioning Manual Connection of an analogue keypad As supplied, only the interface for an to read audit information needs to be analogue keypad of the AnchorPrimor enabled via the menu function [6]. series is enabled. The serial interface to the... -
Page 7: Connection Of Alarm Contacts
Anchor 7000 Installation Manual Installation and Commissioning Manual Connection of alarm contacts Connection via the plug-in terminal (see above) is always used if • The lock system has an external power supply, • A “silent alarm” contact is used to evaluate a hazard alarm system or •... - Page 8 Anchor 7000 Installation Manual Installation and Commissioning Manual Figure 4 - Assignment of the alarm interface If a signal lock with “release enabled” (switching logic) has been set up, this will ensure that the lock is not automatically switched off if the control cable is cut through. At the same, a cable breakage within the safe thus always entails the risk of a block.
-
Page 9: Connecting An Alarm System Within The Scope Of The Vds
Anchor 7000 Installation Manual Installation and Commissioning Manual Connecting an alarm system within the scope of the VdS In the event that an alarm connection is to family must be connected between the two be within the scope of the VdS, the “Gator via a system cable. -
Page 10: Functional Test
Anchor 7000 Installation Manual Installation and Commissioning Manual Functional test Carry out a functional test after completion The safe should open smoothly and reliably of all assembly and installation work. With reclose using the operating lever of the the door open, open and close the lock locking mechanism.
Need help?
Do you have a question about the Anchor 7000 and is the answer not in the manual?
Questions and answers