Vfo/Memory Control; Main/Sub Vfo Control - Yaesu FT-1000MP Operating Manual

Operation
To play back the just-stored message without
transmitting, and without causing the contest
number to increment automatically, press the
#10 key followed by #1. You may do this as
many times as you want and the contest
number will stay the same. If you transmit the
message by pressing the #1 key alone, how-
ever, the contest number will automatically in-
crement, and another press of the #1 key will
cause "599002 BK" to be sent (followed by
"599003 BK' the following time, and so forth).
QO) If the other station asks for a repeat of your
contest exchange, remember that the number
will have incremented automatically after you
sent it. Press the #4 key ([#DWN]) to return to the
previous number, then press key #1 to repeat
the exchange for the other station. If you need
to increment the number manually for some
reason, the #3 ([#UP]) key may be used in the
same manner.
1 If, for some reason, the contest number gener-
ated via key #1 is significantly different from the
desired number, it may be reset via Menu Item
7-3. From this menu selection, you may set the
next-to-be-used contest number to any value
between 0000 and 9999 by rotating the Main
Dial; press to save the new setting and exit.
Il. VFO/Memory Control
Menu Item 7-9 also allows utilization of the
Remote Control Keypad for VFO and Memory
control. The front panel ("tew], (A-B), [A=B], (spuit], [ma],
[McK], [A-m], [Rc.], [sto], and keys, and MEM CH
UP/DWN knob are duplicated on the Remote Con-
trol Keypad.
Il. Main VFO-A Control
Selection of this mode via Menu Item 7-9 dupli-
cates the action of the 12-key front panel BAND
keypad on the front panel of the FT-1000MP. Di-
rect frequency entry and one-touch band change
are possible on both the Main and Sub VFOs,
exactly as on the front panel keypad.
IV. Sub VFO-B Control
This function is essentially identical to "Main
VFO-A Control' as described above. However,
when the key is pushed to begin direct fre-
quency entry, the frequency input will be applied
to the Sub VFO-B register, not the Main VFO-A
register. This allows the operator to use the trans-
ceiver's front panel keypad for the Main VFO, and
the remote keypad for the Sub VFO, thus reducing
the required keystrokes by one.
Note that, in the Sub VFO-B Control mode,
pushing cd then F*] does not shift frequency
entry control to the Main VFO-A (which is the
"sub" VFO of Sub VFO-B). In this mode, frequency
can only be applied to the Sub VFO-B; there is no
Remote || Remote Control Feature (menu selection 7-9)
Control
Unit vontest | Memory | MAIN | SUB
Key#
Puan
ontrol | VFO-A| VFO-B
Keyer Functions
1
CQ Message
(Y*Sew |
| ar
2
Contest#
[AB]
eae
p> 3]
Increment
-
7
:
'
Contest #
ASE
2
Decrement
a
i
*
Contest #
a
el
Ll
5
MSG 0
[M-A ] ian
i s}
6
MSG 1
[McK]
an
on
7
MSG
2
[A-M |
et 7
Ga
8
MSG
3
[Act }
pas
es
3
Mallet
=
aa
a
10
Poca
[ovat]
29 Ol
p>
11 N/A M CH UP cel x)
page 63