CrimeStopper CS-2002DC Series II Installation And Operating Instructions Manual
Crimestopper security products automobile alarm - remote car alarm user manual
Hide thumbs
Also See for CS-2002DC Series II:
- Installation and operating instructions manual (21 pages) ,
- Installation and operating instructions manual (17 pages) ,
- Installation & operating instructions manual (20 pages)
Table of Contents
Advertisement
CS-2002DC & CS-2002DC Series II
REMOTE CONTROL ALARM SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
CONGRATULATIONS on your choice of a Gargoyle™ Remote Alarm System by Crimestopper Security
Products Inc. This booklet contains the information necessary for installing, using, and maintaining your alarm
system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the
Tech Support number below.
*IMPORTANT INFORMATION: Primary and Optional Features:
-PRIMARY: These are features that must be connected in order for the system to operate properly; i.e. the
Siren, L.E.D., +12V Power, Ground, Doorpin, Override/Program/Valet Button etc.
-OPTIONAL: These are features to be connected if desired or agreed upon by the installing dealer. These
features may also require additional parts and/or labor fees. Consult with your installer beforehand; i.e. Door
Locks, Flashing Lights, Hood/Trunk trigger, and Auxiliary Remote Outputs etc.
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
(800) 998-6880
REV. D 7/2002 SW: T2, SC, HC, Latest: CH-(Green dot)
INTRODUCTION
This device complies with FCC Rules part 15. Operation is subject to the following
two conditions: 1) This device may not cause interference, and (2) this device
must accept any interference that may be received, including interference that may
cause undesired operation. The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modification to this equipment. Such
modification could void the user's authority to operate the equipment.
Advertisement
Table of Contents
Related Manuals for CrimeStopper CS-2002DC Series II
Summary of Contents for CrimeStopper CS-2002DC Series II
- Page 1 CONGRATULATIONS on your choice of a Gargoyle™ Remote Alarm System by Crimestopper Security Products Inc. This booklet contains the information necessary for installing, using, and maintaining your alarm system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number below.
-
Page 2: Table Of Contents
Remote Control……………………………………..……………………………………………………….………….12 Operating Instructions………………………..……………………………………………………………..…….13-15 2 Vehicle Operation……….……………………………………………………………………………………………15 Car Jack Protection……………………………………………………………………………………...…………15-16 CS-2002DC Series II Operation……..……………………………………………………………………………17-18 System Wiring Diagram……………………………………………………………………………………….………19 INSTALLATION CAUTIONS & WARNINGS BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, ENGINE COMPUTERS, BATTERY etc.). -
Page 3: Control Module Mounting
CONTROL MODULE MOUNTING DO NOT Mount the control unit in the engine compartment! DO NOT Mount the control unit or wiring harness where they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column! The alarm control module should be mounted in a concealed location. The Placement of the module will affect the distance from which the remote transmitter can control the unit. -
Page 4: Wiring
WIRING RED WIRE: +12V POWER INPUT (15 amp fuse) Connect to +12 Volt source with supplied fuse & holder. Recommended location for this connection is at the vehicle battery positive terminal. BLACK WIRE: SYSTEM CHASSIS GROUND The Black wire MUST be connected the CHASSIS METAL of the vehicle. Scrape away any paint or debris from the connection point and use a star washer to ensure a good connection. -
Page 5: Power Door Lock Wiring
GRAY WIRE: (-) AUX REMOTE OUTPUT 1 (Optional, may require a relay) Connect to the Negative trunk release circuit or to the activation circuit of an auxiliary module or device. If the circuit requires +12V, then a relay is required. RELAY WIRING: Connect the Gray wire to terminal 85, connect relay terminals 86 and 87 to +12V constant power. - Page 6 Negative trigger: Many Imports; Late Fords, GM’s Reverse Polarity: Many Fords, Chrysler/Dodge/Plymouth; GM trucks One wire dual voltage: Late /Chrysler/Dodge/Plymouth Stratus, Cirrus. Minivans; Ford Probe, Some Mazda’s. Semi automatic: Older Saab and Volvo NEGATIVE TRIGGER DOORLOCK WIRING GREEN BLUE REVERSE POLARITY DOOR LOCK WIRING GREEN BLUE MASTER...
- Page 7 SEPARATE DRIVER’S DOOR UNLOCK WIRING NEGATIVE TRIGGER DOOR LOCKS BLUE/WHITE GREEN BLUE DRIVER'S DOOR MOTOR +12V FUSED UNLOCK WIRE WIRING FOR REVERSE POLARITY DOOR LOCKS BLUE/WHITE GREEN BLUE MASTER SWITCH 30 87A UNLOCK WIRE FACTORY LOCK RELAYS FUSED +12V LOCK WIRE...
-
Page 8: Transmitter Programming
This system will learn a maximum of 3 transmitters total. 1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3 chirps. 2. Press the Program/Override Button 5 times and you should hear 5 light flashes and 5 siren chirps. 3. -
Page 9: Option Programming
PROGRAMMABLE OPTIONS 1. Turn the Ignition ON and press the Override/Program button 5 times. You should hear a long confirmation chirp. 2. Within the next few seconds, press the Override/Program button [again] the number of times that corresponds to the feature list below. The siren will chirp for each button press. DO NOT LOSE COUNT!! 3. - Page 10 OPTION PROGRAMMING 1. HORN CHIRPS / PULSES This option controls the system’s Factory Vehicle Horn output. There are 3 selections: Button 1 (Lock) = Horn Pulse only when alarm is tripped. Button 2 (Unlock) = Horn Chirps for Arm / Disarm and Pulse when tripped. Button 3 (Trunk) = Horn Chirps for Arm, Disarm, and Pre-warning protection while it still pulses when tripped.
- Page 11 OPTION PROGRAMMING 9. PARKING LIGHTS ON WITH DISARM Keeps parking lights on instead of 2 flashes when system is disarmed to assist in locating your vehicle in a crowded parking lot or structure. Light will stay on for 30 Sec. or until Ignition is turned on. 10.
-
Page 12: Custom Override
If system still does not disarm, then repeat steps above. REMOTE CONTROL 4 BUTTON CS-2002DC REMOTE TRANSMITTER: DISARM (UNLOCK) (LOCK) PANIC TRUNK REMOTE PANIC (SEE PAGE 17 FOR CS-2002DC SERIES II REMOTE CONTROL) -
Page 13: Operating Instructions
OPERATING INSTRUCTIONS ACTIVE ARMING To arm the alarm and lock the doors, press the #1 (Lock Symbol) button on the transmitter. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock and the starter will be disabled if these optional features are installed. - Page 14 OPERATING INSTRUCTIONS PROGRAMMABLE SILENT ARM/DISARM MODE The system can be silently armed and disarmed as normal with Lock/Unlock Buttons, but no siren chirp. See alarm programming option (8) to enable or disable this feature. EMERGENCY OVERRIDE / DISARM If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to open the door with the key, which will activate the alarm.
-
Page 15: Vehicle Operation
OPERATING INSTRUCTIONS OPEN ZONE ALERT/BYPASS If the system detects a faulty or open zone (Door left open) when the system is ACTIVELY ARMED, the siren will chirp 4 times along with 4 light flashes. The faulty zone will be automatically bypassed. IGNITION-CONTROLLED DOORLOCKS The doors will automatically lock when the ignition is turned on and will unlock when the ignition is turned off. -
Page 16: Car Jack Protection
CARJACK PROTECTION PASSIVE CARJACK This feature provides Passive Carjack protection and must be enabled before use through Alarm programming options (13) & (14). See page 9. We recommend this mode should only be used in serious situations. When the Ignition is on (vehicle is running), and a door is opened, the Carjack countdown sequence will be initiated. -
Page 17: Cs-2002Dc Series Ii Operation
“SUPER BRIGHT” BLUE LED / VALET BUTTON POD LED POD SYSTEM VALET/PROGRAM BUTTON CS-2002DC SERIES II BUTTON 1 BUTTON 3 PANIC *GREEN LED Blinks once for Bank 1 and twice for Bank 2. DUAL ADJUST Smart Sense™ Shock Sensor: >Use the Green screw for Pre-warn adjustment >Use the Red Level for Shock trigger adjustment... - Page 18 CS-2002DC SERIES II LED / VALET BUTTON MOUNTING: IN DASH UNDER DASH "L" Bracket...
-
Page 19: System Wiring Diagram
(+) SWITCHED IGN "ON" OPT. GRAY (-) REMOTE OUTPUT 1 RELAY BLUE (-) HOOD/TRUNK TRIGGER (-) NEG. PIN SWITCH (-) DOME LIGHT OUTPUT DOME LIGHT CS-2002DC CS-2002DC II BLACK/WHITE BROWN/WHITE (-) HORN HONK OUTPUT BLACK(GROUND) WHITE(WARNING) BLUE (TRIGGER) RED (+) OVERRIDE/ PROGRAM BUTTON...