Table of Contents
Advertisement
Quick Links
This booklet is written and designed for professional installation technicians who have been trained in
automotive electrical testing, trouble-shooting, and installation.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Siren,
L.E.D., Power, Ground, Doorpin, etc.
-OPTIONAL: These are features to be connected only if desired or agreed upon by the installing dealer (i.e.
Door Locks, Flashing Lights, Starter Disable, Hood, Trunk, and Auxiliary Remote Outputs etc.)
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
(800) 998-6880
website: www.crimestopper.com
email: tech-support@crimestopper.com
CS-2007DC / WDC
REMOTE CONTROL ALARM SYSTEM
INSTALLATION HANDBOOK
INTRODUCTION
This device complies with FCC Rules part 15. Operation is subject to the following
two conditions: 1) This device may not cause interference, and (2) this device
must accept any interference that may be received, including interference that may
cause undesired operation. The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modification to this equipment. Such
modification could void the user's authority to operate the equipment.
Advertisement
Table of Contents
Related Manuals for CrimeStopper CS-2007
Summary of Contents for CrimeStopper CS-2007
- Page 1 -OPTIONAL: These are features to be connected only if desired or agreed upon by the installing dealer (i.e. Door Locks, Flashing Lights, Starter Disable, Hood, Trunk, and Auxiliary Remote Outputs etc.) TECH SUPPORT Mon-Fri 8:00 AM-4:30 PM Pacific Time (800) 998-6880 website: www.crimestopper.com email: tech-support@crimestopper.com CS-2007DC / WDC INSTALLATION HANDBOOK INTRODUCTION This device complies with FCC Rules part 15.
-
Page 2: Installation Cautions & Warnings
INSTALLATION CAUTIONS & WARNINGS BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, AND BATTERY). TO PREVENT A POSSIBLE DEAD BATTERY remove vehicle dome light fuse while working on the vehicle. MAKE CERTAIN TO REINSTALL FUSE PRIOR TO TESTING FOR DOOR TRIGGERS. DO NOT EXCEED MAXIMUM OUTPUT RATINGS! - SERIOUS DAMAGE MAY OCCUR. -
Page 3: Component Mounting
COMPONENT MOUNTING SIREN MOUNTING: Mount the siren under the hood to fender-well or other body surface with the open end facing downward. Run the red siren wire through the firewall using a rubber grommet. Ground the black wire to the body metal near the siren. - Page 4 WIRING GRAY WIRE: (-) AUX REMOTE OUTPUT 1 (Optional, requires relay) Connects to terminal 85 of a relay. Connect terminal 86 to constant. Connect terminal 87 to +12V constant or ground depending on the type of circuit that needs to activated. Connect terminal 30 to the device/circuit to be activated. GREEN WIRE: (-) DOOR TRIGGER Identify the wire that reads ground when any door is open and 12 volts when all doors are closed.
-
Page 5: Power Door Lock Wiring
BROWN 14 GAUGE (2 WIRES) The Two 14 GA. Brown wires connect directly to the Vehicle’s STARTER wire to bypass this circuit when the alarm system is armed or tripped (Starter Kill). Locate the “Start” Wire in the vehicle (Power During Crank position only). - Page 6 NEGATIVE TRIGGER DOORLOCK WIRING GREEN BLUE IN4001 DIODES LOCK UNLOCK REVERSE POLARITY DOOR LOCK WIRING GREEN BLUE MASTER SWITCH Diodes are recommended for protection of the door lock outputs on Positive & Negative systems. (Not included) POWER DOOR LOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING FACTORY POWER...
- Page 7 SEPARATE DRIVER’S DOOR UNLOCK WIRING WIRING FOR REVERSE POLARITY DOOR LOCKS WHITE/BLUE GREEN BLUE DRIVER'S DOOR MOTOR 30 87A UNLOCK WIRE WIRING FOR POSITIVE TRIGGER DOOR LOCKS WHITE/BLUE GREEN BLUE DRIVER'S DOOR MOTOR +12V FUSED UNLOCK WIRE FUSED +12V FACTORY LOCK RELAYS...
-
Page 8: Option Programming
ELECTRONIC PROGRAMMABLE OPTIONS 1. Turn the ignition on 2. Wait at least (1) second, then press the override/program button the number of times that corresponds to the feature you want to change. (See the list below) The siren will chirp once for each button press. 3. - Page 9 OPTION PROGRAMMING OPTION DESCRIPTIONS - SEE CHART ON PAGE 8 4. DOOR LOCK WITH PASSIVE ARM This option controls whether the doors will lock when Passive Arming occurs. Note: May increase the risk of locking keys in the vehicle. Factory default setting is ON. 5.
-
Page 10: Vehicle Programming
PREPARING THE TRANSMITTERS 1. Take the transmitter to be used for Vehicle #1 and set them aside. No modifications are necessary. 2. Open the transmitters for Vehicle #2 and solder the “2 VEH” pads together on each. This designates these transmitters as Vehicle #2. -
Page 11: Jumper Plug Programming
TRANSMITTER / 3 SEC. DOOR LOCK PROGRAMMING TRANSMITTER CODE PROGRAMMING 1. Have system DISARMED/UNLOCK and Ignition OFF before attempting these steps. 2. Turn Ignition ON and OFF 3 times quickly, leaving it ON the last time. (ON/OFF, ON/OFF, ON) You should hear (1) short chirp. -
Page 12: Jumper Location
JUMPER LOCATION TOP OF CONTROL MODULE SIDE VIEW JUMPER PLUG JUMPER PINS (J10) 2 VEHICLE (J9) CARJACK STARTER DISABLE SWITCH START WIRE STARTER BROWN / WHITE BROWN / WHITE... - Page 13 OPTIONAL DOME LIGHT ILLUMINATION RED/BLACK (-) DOME ILLUMINATION DOOR PIN SWITCH DOME LIGHT ILLUMINATION WITH ACTIVE RE-ARM +12V BAT. WHITE/GREEN (-) DOME ILLUMINATION GREEN or VIOLET DOOR TRIGGER WIRE DRIVER'S DOOR PIN SWITCH DOME LIGHT +12V BAT. CONNECTS TO EITHER +12V or GROUND, DEPENDING ON THE TYPE OF DOME LIGHT CIRCUIT...
- Page 14 OPTIONAL HORN HONK WIRING WHITE/BLACK HORN HONK OUTPUT HORN WIRE IN STEERING COLUMN OPTIONAL M.A.P. WIRING WHITE/ORANGE M.A.P. OUTPUT START +12V BAT. FACTORY HORN RELAY MOBILE ACCESSORY PROTECTION ACC. SWITCHED Connect relay as shown to interrupt the power wire of mobile accessories such as Audio system or Cellular telephone.
-
Page 15: Installer Test Mode
Installer Test Mode is helpful for a number of reasons: Quick, Easy testing of the system without having to continually arm/disarm Test the systems reset, re-arm, and bypass logic Review up last 4 triggers codes to diagnose false alarm problems TO ENGAGE TEST MODE: 1.