CrimeStopper GARGOYLE CS-2001FC Installation & Operating Instructions Manual
  1. Manuals
  2. Brands
  3. CrimeStopper Manuals
  4. Car Alarm
  5. Gargoyle CS-2001FC II Series
  6. Installation & operating instructions manual
CrimeStopper GARGOYLE CS-2001FC Installation & Operating Instructions Manual

CrimeStopper GARGOYLE CS-2001FC Installation & Operating Instructions Manual

Remote control alarm system
Hide thumbs Also See for GARGOYLE CS-2001FC:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation Instructions and Operating Manual
CS-2001FC
REMOTE CONTROL ALARM SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
CONGRATULATIONS on your choice of a Gargoyle™ Remote Alarm System by Crimestopper Security
Products Inc. This booklet contains the information necessary for installing, using, and maintaining your alarm
system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the
Tech Support number below.
*IMPORTANT INFORMATION: Primary and Optional Features:
-PRIMARY: These are features that must be connected in order for the system to operate properly; i.e. the
Siren, L.E.D., +12V Power, Ground, Doorpin, Override/Program/Valet Button etc.
-OPTIONAL: These are features to be connected if desired or agreed upon by the installing dealer. These
features may also require additional parts and/or labor fees. Consult with your installer beforehand; i.e. Door
Locks, Flashing Lights, Starter disable, Hood/Trunk trigger, and Auxiliary Remote Outputs etc.
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
(800) 998-6880
INTRODUCTION
This device complies with FCC Rules part 15. Operation is subject to the following
two conditions: 1) This device may not cause interference, and (2) this device
must accept any interference that may be received, including interference that may
cause undesired operation. The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modification to this equipment. Such
modification could void the user's authority to operate the equipment.

Advertisement

Table of Contents
loading

Related Manuals for CrimeStopper GARGOYLE CS-2001FC

Summary of Contents for CrimeStopper GARGOYLE CS-2001FC

  • Page 1 CONGRATULATIONS on your choice of a Gargoyle™ Remote Alarm System by Crimestopper Security Products Inc. This booklet contains the information necessary for installing, using, and maintaining your alarm system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number below.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Installation Cautions & Warnings…….………………………………………………………………………………2 Control Module Mounting………….……………………………………………..……………………….…………..3 Component Mounting………….…………………………………………………………….…………………..……..3 Wiring……..……………………………………………………………………………………………………….…….4-5 Power Door Lock Wiring...……………………………………………………….………..…………………………5-7 Transmitter Programming………………………………………………………………………………………………8 Option Programming…………………………………………….……………………………….………………….9-11 Custom Override……...………………………………………….……………………………….……………………11 Remote Control……………………………………..……………………………………………………….………….12 Operating Instructions………………………..……………………………………………………………..…….12-14 2 Vehicle Operation……….……………………………………………………………………………………………15 Car Jack Protection……………………………………………………………………………………………………15 System Wiring Diagram……………………………………………………………………………………….………16 INSTALLATION CAUTIONS & WARNINGS BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, ENGINE COMPUTERS, BATTERY etc.).

  • Page 3: Control Module Mounting

    CONTROL MODULE MOUNTING DO NOT Mount the control unit in the engine compartment! DO NOT Mount the control unit or wiring harness where they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column! The alarm control module should be mounted in a concealed location. The Placement of the module will affect the distance from which the remote transmitter can control the unit.

  • Page 4: Wiring

    WIRING RED WIRE: +12V POWER INPUT (15 amp fuse) Connect to +12 Volt source with supplied fuse & holder. Recommended location for this connection is at the vehicle battery positive terminal. BLACK WIRE: SYSTEM CHASSIS GROUND The Black wire MUST be connected the CHASSIS METAL of the vehicle. Scrape away any paint or debris from the connection point and use a star washer to ensure a good connection.

  • Page 5: Power Door Lock Wiring

    GRAY WIRE: (-) AUX REMOTE OUTPUT 1 (Optional, may require a relay) Connect to the Negative trunk release circuit or to the activation circuit of an auxiliary module or device. If the circuit requires +12V, then a relay is required. RELAY WIRING: Connect the Gray wire to terminal 85, connect relay terminals 86 and 87 to +12V constant power.
  • Page 6 Negative trigger: Many Imports; Late Fords, GM’s Reverse Polarity: Many Fords, Chrysler/Dodge/Plymouth; GM trucks One wire dual voltage: Late /Chrysler/Dodge/Plymouth Stratus, Cirrus. Minivans; Ford Probe, Some Mazda’s. Semi automatic: Older Saab and Volvo NEGATIVE TRIGGER DOORLOCK WIRING GREEN BLUE REVERSE POLARITY DOOR LOCK WIRING GREEN BLUE MASTER...
  • Page 7 SEPARATE DRIVER’S DOOR UNLOCK WIRING NEGATIVE TRIGGER DOOR LOCKS BLUE/WHITE GREEN BLUE DRIVER'S DOOR MOTOR +12V FUSED UNLOCK WIRE WIRING FOR REVERSE POLARITY DOOR LOCKS BLUE/WHITE GREEN BLUE MASTER SWITCH 30 87A UNLOCK WIRE FACTORY LOCK RELAYS FUSED +12V LOCK WIRE...

  • Page 8: Transmitter Programming

    1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3 chirps. 2. Press the Program/Override Button 5 times and you should hear 5 light flashes and 5 siren chirps. 3. Press #1 (LOCK) on the new transmitter. Siren chirps one time for Code-learn confirmation. Press #1 Button on a second or third remote at this time.

  • Page 9: Programmable Options

    PROGRAMMABLE OPTIONS 1. Turn the Ignition ON and press the Override/Program button 5 times. You should hear a long confirmation chirp. 2. Within the next few seconds, press the Override/Program button [again] the number of times that corresponds to the feature list below. The siren will chirp for each button press. DO NOT LOSE COUNT!! 3.
  • Page 10 OPTION PROGRAMMING 1. HORN CHIRPS / PULSES This option controls the system’s Factory Vehicle Horn output. There are 3 selections: Button 1 (Lock) = Horn Pulse only when alarm is tripped. Button 2 (Unlock) = Horn Chirps for Arm / Disarm and Pulse when tripped. Button 3 (Trunk) = Horn Chirps for Arm, Disarm, and Pre-warning protection while it still pulses when tripped.

  • Page 11: Custom Override

    OPTION PROGRAMMING 9. PARKING LIGHTS ON WITH DISARM Keeps parking lights on instead of 2 flashes when system is disarmed to assist in locating your vehicle in a crowded parking lot or structure. Light will stay on for 30 Sec. or until Ignition is turned on. 10.

  • Page 12: Remote Control

    4 BUTTON REMOTE TRANSMITTER: ACTIVE ARMING To arm the alarm and lock the doors, press the #1 (Lock Symbol) button on the transmitter. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock and the starter will be disabled if these optional features are installed.
  • Page 13 OPERATING INSTRUCTIONS PRE-WARNING SHOCK PROTECTION & SENSOR ADJUSTMENT If a low-level shock to the vehicle is detected, pre-warning protection will activate sounding 6 quick siren chirps and 1 light flash. If a hard impact is detected the shock sensor should trip the alarm system. Once it is mounted, adjust the sensor as needed by turning the adjustment screw clockwise to increase or counter- clockwise to decrease the sensitivity.
  • Page 14 OPERATION PASSIVE ARMING / PASSIVE LOCK MODES / PASSIVE CHIRP COUNTDOWN If programmed, passive (Automatic) Arming will occur 30 Seconds after the ignition is turned off and the last door has been closed. The LED will begin flashing rapidly while counting down. If a door is reopened, the system will wait (LED solid) for the door or zone to close before arming.

  • Page 15: Vehicle Operation

    2 VEHICLE OPERATION 2 VEHICLE CONTROL Your remote control can be programmed to Arm/Disarm a second vehicle with an identical Crimestopper system installed. Follow transmitter programming steps on the second vehicle. Instead of pressing the #1 Lock at step 3, press Button #4 (Panic) on YOUR existing remote. Your remote will now have arm/disarm control of the second vehicle with a quick press and release of your Button #4 (Panic).

  • Page 16: System Wiring Diagram

    (-) NEG. DOOR PIN SWITCH (+) POSITIVE DOOR PIN SWITCH GREEN (-) DOOR TRIGGER VIOLET (+) DOOR TRIGGER IGN. BLACK CHASSIS GROUND FUSE YELLOW (+) SWITCHED IGN "ON" GRAY OPT. (-) REMOTE OUTPUT 1 RELAY BLUE (-) HOOD/TRUNK TRIGGER (-) NEG. PIN SWITCH (-) DOME LIGHT OUTPUT DOME LIGHT...

Table of Contents