Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ShowPro H1 PROFILE
Summary of Contents for ShowPro H1 PROFILE
- Page 1 H1 PROFILE MANUAL PSHMOV100...
-
Page 2: Table Of Contents
CONTENTS SAFETY - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 INTRODUCTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4 SPECIFICATIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5 PHOTOMETRICS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6... -
Page 3: Safety
SAFETY WARNING! Before carrying out any operations with the unit, carefully read this instruction manual and keep it with care for future reference, it contains important information about the installation, use and maintenance of the unit. General instructions - The products referred to in this manual conform to the European Community Directives and are therefore marked with CE. -
Page 4: Introduction
Warnings and installation precautions - If this device is operated in any way different to the way described in this manual, it may suffer damage and the warranty becomes void. Any unauthorized operation may lead to dangers like short circuit, burns, electric shock, etc. - Before starting any maintenance work or cleaning the fixture, cut off power from the main supply. -
Page 5: Specifications
SPECIFICATIONS Light Source: 480W PHILIPS lamp Output: 16300lm Illuminance: 130k @ 20m Colour Temperature: 6500K ± 400K Beam Angle: Beam mode: 2.1°~29° Spot mode: 2.3°~41.5° Pan: 540° (16 bit) Tilt: 270° (16 bit) Colour: CMY + 15 filters Gobos: 1 static gobo wheel (19 + open) 1 rotating gobo wheel (8 + open) Animation: 1 animation wheel... -
Page 6: Photometrics
PHOTOMETRICS... -
Page 7: Colour & Gobos
COLOUR & GOBOS Colour Animation Rotating Gobos Static Gobos... -
Page 8: Dimensions
DIMENSIONS... -
Page 9: Overview
OVERVIEW Fixture Illustration Control Panel 4. Fuse 3/5 Pin DMX In 5. Power In 3/5 Pin DMX Out 6. Omega Bracket Plate Control Panel Increase value or scroll up DOWN: Decrease value or scroll down LEFT: Return to previous menu RIGHT: Move between units, tens, hundreds Confirm and save setting... -
Page 10: Installation
INSTALLATION The H1 must be set up on a solid and even surface. By means of the brackets on the baseplate, the unit can also be mounted upside down to a cross arm. For mounting, strong, stable clamps are required. The bolts of the brackets are placed into the openings provided in the base plate and turned clockwise until they lock. -
Page 11: Connection
CONNECTION Power Connection Using Powercon In. Attention: due to power rating, one power cable can connect 1 unit maximum Do not connect more than 1 units in series with one power cable. Do not use with damaged power cable. Power off the fixture when not in use. DMX Connection... - Page 12 • Depending on the length of the DMX cable run, or other factors, it may be advisable to install a terminator at the last fixture in the run. • The illustration below shows the correct placement of a 120Ω 0.25W resistor in a terminator, as well as the standard DMX signal pin connections DMX Starting Address •...
-
Page 13: Menu
MENU Main Menu Menu Level 1 Menu Level 2 Menu Level 3 Default DMX Address 1 – 512 Custom IP Address 2.x.x.x Custom IP Mask 255.0.0.0 SETUP Universe 000 – 255 Ethernet Interface Start Channel 1 – 512 Ethernet to DMX Lamp DMX Safety Black Out Invert Pan... - Page 14 Main Menu Menu Level 1 Menu Level 2 Menu Level 3 Default Lamp Reset 1.Cyan 0 – 255 2.Magenta 0 – 255 3.Yellow 0 – 255 4.Colour 1 0 – 255 5.Colour 2 0 – 255 6.Colour 3 0 – 255 7.Strobe 0 –...
-
Page 15: Dmx Chart
DMX CHART 31CH Function Value Setting Notes Cyan 0 – 255 Cyan 0% - 100% Valid when Colour 1 = 0 Magenta 0 – 255 Magenta 0% - 100% Valid when Colour 2 = 0 Yellow 0 – 255 Yellow 0% - 100% Valid when Colour 3 = 0 000 –... - Page 16 31CH Function Value Setting Notes 196 – 200 Gobo 8 Shake Slow to Fast 201 – 205 Gobo 9 Shake Slow to Fast 206 – 210 Gobo 10 Shake Slow to Fast 211 – 215 Gobo 11 Shake Slow to Fast 216 –...
-
Page 17: Maintenance
MAINTENANCE Maintenance and Cleaning the Unit - Make sure there are no persons standing below the unit when taking down/setting up. - Switch off the unit, unplug the main cable and wait till the unit has cooled down. - All screws used for installing the device and any of its parts should be tightly fastened and should not be corroded.
Need help?
Do you have a question about the H1 PROFILE and is the answer not in the manual?
Questions and answers