Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Martin Exterior Wash Pro QUAD XL
Summary of Contents for Martin Exterior Wash Pro QUAD XL
- Page 1 Exterior Wash Pro QUAD and CTC – S, M, L, XL Safety and Installation manual Exterior Wash Exterior Wash Exterior Wash Exterior Wash Pro QUAD XL Pro QUAD L Pro QUAD M Pro QUAD S Exterior Wash Exterior Wash Exterior Wash Exterior Wash Pro CTC XL Pro CTC L...
-
Page 2: Dimensions
Martin is a registered trademark of HARMAN PROFESSIONAL DENMARK ApS registered in the United States and/or other countries. - Page 3 Exterior Wash Pro L Exterior Wash Pro XL Exterior Wash Pro L with Exterior Wash Pro XL with and without Baffle Snoot and without Baffle Snoot All dimensions are in millimeters. ® Martin Exterior Wash Pro family Safety and Installation Manual Rev. A...
-
Page 4: Table Of Contents
Installing a temporary power plug ............17 Data connections ................... 17 Testing ......................18 Maintenance ....................19 Cleaning .................... 19 Pressure relief valve................19 Firmware maintenance ............... 20 ® Martin Exterior Wash Pro family Safety and Installation Manual Rev. A... -
Page 5: Safety Information
User Manual must be referred to an authorized Martin service agent. The light source contained in the fixture may be replaced by Martin or an authorized Martin service agent only. - Page 6 Pro pages of the Martin® website at www.martin.com. Before you install, operate or service an Exterior Wash Pro family fixture, check the Martin website and make sure that you have the latest user documentation for the fixture. Document revisions are indicated at the bottom of page 2.
- Page 7 Do not modify the fixture in any way not described in this manual or install other than genuine Martin® parts. Do not stick filters, masks or other materials onto any lens or other optical component. Use only accessories approved by Martin® to modify the light beam.
- Page 8 0.2 m (7.9 in.) from the fixture and so that prolonged staring into the light output at less than 26.5 m (87 ft.) from the fixture is not expected. ® Martin Exterior Wash Pro family Safety and Installation Manual Rev. A...
- Page 9 0.024 m² 0.038 m² Exterior Wash Pro M 0.048 m² 0.072 m² Exterior Wash Pro L 0.084 m² 0.120 m² Exterior Wash Pro XL 0.144 m² 0.180 m² ® Martin Exterior Wash Pro family Safety and Installation Manual Rev. A...
-
Page 10: Introduction
Narrow, Medium, Wide, Very Wide and Asymmetric beam angle micro lens accessories are available from Martin. A Baffle Snoot accessory that limits light spill and integrates with the fixture’s design is also available. These accessories are designed to mount quickly on the front of the fixture. See the Exterior Wash Pro pages on the Martin website at www.martin.com for details and ordering... -
Page 11: Physical Installation
Physical installation Warning! Read ‘Safety information’ on page 5 before installing the fixture. Contact your Martin® supplier for assistance if you have any questions about how to install this product safely. Fixture location Exterior Wash Pro family fixtures are intended for outdoor use. With an IP66 rating, they are protected against dust, humidity and water and are able to withstand powerful water jets, but they are not submersible. -
Page 12: Securing With A Safety Cable
To secure the fixture with a safety cable: 1. Obtain an Exterior Wash Pro Safety Cable Attachment Bracket from your Martin supplier. Fasten this bracket (arrowed) securely to the bottom of the fixture as shown in the illustration below using the screws supplied with the bracket. -
Page 13: Adjusting Tilt
Figure 3. Tilt adjustment Installing a microlens beam angle accessory Optional microlenses that modify the beam angle are available from Martin (see the Exterior Wash Pro pages on the Martin website at www.martin.com for details and ordering information). The following options are available: •... -
Page 14: Installing A Baffle Snoot
3. See B. Using the Exterior Multitool available from Martin or a similar tool with no sharp edges, lever the trim frame carefully away from the fixture. Avoid damaging the fixture housing, seal or trim frame. - Page 15 Press each screw in and turn it counter- clockwise until it reaches a stop. Check that the snoot is held securely. Figure 6. Installing a Baffle Snoot ® Martin Exterior Wash Pro family Safety and Installation Manual Rev. A...
-
Page 16: Ac Power
Use connectors or junction boxes that are protected to IP67 or higher. ● Fill junction boxes with potting compound to seal the ends of cables and to protect connections from corrosion. ® Martin Exterior Wash Pro family Safety and Installation Manual Rev. A... -
Page 17: Connecting To Power
Power plug connections Data connections See the Exterior Wash Pro User Manual available for download from www.martin.com for details of connecting the fixture to control data. Use shielded, twisted-pair, high-quality dedicated DMX cable only for the control data link. Microphone cable is not suitable. -
Page 18: Testing
Fixture status is indicated as follows. LED color Signal Status Cold Fast flash Busy (booting or uploading SW) Cold Slow flash No DMX detected Cold/warm Alternating Running normally in DMX mode ® Martin Exterior Wash Pro family Safety and Installation Manual Rev. A... -
Page 19: Maintenance
Installation, on-site service and maintenance can be provided worldwide by the Martin Professional Global Service organization and its approved agents, giving owners access to Martin’s expertise and product knowledge in a partnership that will ensure the highest level of performance throughout the product’s lifetime. Please contact your Martin®... -
Page 20: Firmware Maintenance
• The latest Exterior Wash Pro firmware files (Martin Companion automatically downloads these from the Martin fixture firmware cloud when you run it on a PC that is connected to the Internet). • A Martin Companion Cable USB-DMX hardware interface (available from your Martin supplier). - Page 21 Specifications For full product specifications, see the Exterior Wash Pro area of the Martin website at www.martin.com. FCC compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 22 www.martin.com...