Subscribe to Our Youtube Channel
Related Manuals for Martin EC-10
Summary of Contents for Martin EC-10
- Page 1 EC Series LED Video Panels EC Series Headers Installation and Safety Manual EC-10 EC-20...
- Page 2 The Martin logo, the Martin name and all other trademarks in this document pertaining to services or products by Martin Professional A/S or its affiliates and subsidiaries are trademarks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries.
- Page 3 EC-20 All dimensions are in millimeters...
-
Page 4: Safety Information
If you have questions about how to operate the EC Series system safely, please contact your Martin supplier or call the Martin 24-hour service hotline on +45 8740 0000, or in the USA on 1-888-tech-180. - Page 5 • Do not modify the product in any way not described in this manual. • Install only genuine Martin parts in or on the product unless an alternative is described in this manual. • Do not operate the product if the ambient temperature (T ) exceeds 40°...
-
Page 6: Table Of Contents
Contents Safety Information ..............4 Introduction . -
Page 7: Introduction
Martin™. This product features: • 10 mm (0.4 inch) pixel pitch and 48 x 72 pixels per panel image resolution on EC-10 panels • 20 mm (0.79 inch) pixel pitch and 24 x 36 pixels per panel image resolution on EC-20 panels •... -
Page 8: Using For The First Time
Important! To ensure that EC Series panels can withstand the shocks that normally occur during transport, they must be packed in a Martin EC Series flightcase (see Figure 1) following the instructions in the flightcase. Damage caused to panels that are incorrectly packed or exposed to abnormal shocks is not covered by the product warranty. -
Page 9: Physical Installation
An unlimited number of correctly supported columns of panels may be installed horizontally alongside each other. There is provision for both flat and curved video wall configurations. It is possible to mix and interconnect EC-10 and EC-20 panels in an installation. The P3 System Controller will recognize the different panel types. -
Page 10: Suspension Options
The suspension options are: 1. Single columns of panels suspended from a Martin Single Header using two rigging clamps per column from a truss. 2. Single columns of panels suspended from a Martin Single Header using two eyebolts per column from steel cables, chains or hoists. - Page 11 7. Note that Headers have a male cone at one end and a female cone at the other end. Engaging male and female cones will ensure correct side-to-side alignment of the Headers. 8. Similarly, note that EC Series video panels have cones for correct side-to-side alignment. 9.
- Page 12 Martin Double and Triple Headers are supplied in flightcases with Header Connection Brackets installed (see Figure 7). If using Martin EC Series Double or Triple Headers to suspend independent groups of columns 2 or 3 panels wide from steel cables, chains or a hoist: 1.
- Page 13 Suspending EC Series panels from Headers and other panels The procedure for fastening an EC Series video panel to an EC Series Header or another EC Series panel above it is the same: 1. Remove all rubber connector covers and store them safely for re-use. 2.
- Page 14 4. See Figure 11. Continue lifting the panel so that its spring-loaded locking hooks are pushed open by the locking posts D in the Header or panel above. Figure 11: Hooks open around locking posts (cutaway view) 5. See Figure 12. Lift the panel until you hear both locking hooks click as they lock around the locking posts D in the Header or panel above.
- Page 15 6. Then turn both locking handles A firmly down and in towards the center of the panel to lock the hooks in position around the locking posts D. Figure 13: Close locking handles to lock hooks round locking posts (cutaway view) 7.
- Page 16 EC Series Curving Kit (P/N 90354270). • EC-10 panels can be installed in a concave curve with panels angled at up to 15° to each other. • EC-20 panels can be installed in a concave or convex curve with panels angled at up to 20°...
-
Page 17: Dismantling An Installation
Example installation The example below shows a display screen seven EC Series panels wide and four panels high. EC-20 panels are shown in the illustration but the use of suspension points and Headers is identical for EC-10 panels. Required items •... -
Page 18: Ac Power
AC power WARNING! The safety of the installation is the responsibility of the installer. Read “Safety Information” on page 4 before creating an installation or connecting an EC Series panel to AC mains power. Disconnect the entire installation from power before carrying out installation work. WARNING! Connect to 200-240 VAC, 50/60 Hz mains power only. - Page 19 Panel interconnection Power input and throughput connectors on EC Series panels are integral and engage automatically when panels are installed in columns (see Figure 10 on page 13). Power is supplied to columns of panels via the Header power input cable (see A in Figure 2 on page 9). Power is relayed from the Header to the first EC Series panel and then from one panel to the next via power throughput connectors (see A, B and C in Figure 18) and input connectors (see E, G and H in Figure 18).
-
Page 20: Inrush Current
Each EC Series panel is protected by two 3.15 amp slow-blow mains fuses. The breaking capacity is 1500 A @ 250 V. Fuses are not user-replaceable. Contact Martin for service if you suspect that a fuse has blown. EC Series user manual... -
Page 21: P3™ Communication Link
It is possible to mix and interconnect EC-10 and EC-20 panels in an installation. The P3 System Processor will recognize the panel types in the installation, display them correctly in the user interface, and control the different panel types correctly. -
Page 22: Connecting The P3 Link
Important! More expensive, sophisticated switches tend to carry out additional processing that can cause latency. You should therefore choose a relatively cheap unmanaged 1GB Ethernet switch. P3 system layout: schematic overview P3 System Controller P3 signal Analog video Mouse Analog Keyboard video Monitor... -
Page 23: Monitoring Status And Testing
For details of these, see the user documentation supplied with the P3 System Controller or available for download from www.martin.com When repacking panels in a Martin flightcase after operation, follow the instructions in the flightcase (see “Transporting EC Series panels” on page 8). -
Page 24: Service And Maintenance
Software updates are available from Martin and can be installed from the P3 System Controller over the P3 link. EC-10 and EC-20 panels use the same software. The software automatically detects the panel type once it is installed. - Page 25 EC-20 depending on which type of block is installed. However, all LED blocks should be of the same type. It is physically possible to install a mixture of EC-10 and EC-20 LED blocks on one panel, but the panel will only activate the type of blocks which there is most of.
-
Page 26: Troubleshooting
Fault on P3 link. One or more panels displays connections. Repair or replace damaged cables. video incorrectly or does not Have faulty panel serviced by Martin service display video at all. Panel defective. technician. Other device (e.g. Ethernet switch) on P3 link Replace with a device known to be operating defective. -
Page 27: Specifications
Protocol ........ - Page 28 Canadian safety ....... . CSA 60950-1-03 Included Items EC-10 Video Panel (P/N 90354320) 1 x EC-10 LED Video Panel without packaging EC Series user manual...
- Page 29 Spare Parts EC-10 Left-side (viewed from front) LED module, calibrated......P/N 90354310 EC-10 Right-side (viewed from front) LED module, calibrated ..... . . P/N 90354300 EC-20 Left-side (viewed from front) LED module, calibrated.
- Page 30 Martin™ P3-200™ System Controller ......... . P/N 90721020 Martin™ P3-PC™ License on One-Key™ USB stick ......P/N 90721030 Martin™...
- Page 32 • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark Tel: +45 8740 0000 • Fax +45 8740 0010...
Need help?
Do you have a question about the EC-10 and is the answer not in the manual?
Questions and answers