Titan 0509009 Owner's Manual
  1. Manuals
  2. Brands
  3. Titan Manuals
  4. Water Pump
  5. 0509009
  6. Owner's manual

Titan 0509009 Owner's Manual

Gas piston pump
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ADVANTAGE GPX 165
Model Numbers:
Bare
Complete
Bare w/5 Gal. Siphon
Complete w/5 Gal. SIphon
Gas Piston Pump
0509009
0509039
0509055
0509059
Owner's Manual
Do not use this equipment
before reading this manual!
NOTE: This manual contains important
warnings and instructions. Please
read and retain for reference.
© Titan Tool Inc. All Rights Reserved. Form No. 0528902B
0611
•

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 0509009 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Titan 0509009

Summary of Contents for Titan 0509009

  • Page 1 NOTE: This manual contains important Bare 0509009 warnings and instructions. Please Complete 0509039 read and retain for reference. Bare w/5 Gal. Siphon 0509055 Complete w/5 Gal. SIphon 0509059 © Titan Tool Inc. All Rights Reserved. Form No. 0528902B 0611 •...

  • Page 2: Safety Precautions

    • Use lowest possible pressure to flush equipment. consultation with a plastic surgeon or reconstructive • Do not spray onto pump assembly. hand surgeon may be advisable. © Titan Tool Inc. All rights reserved.

  • Page 3: Specifications

    • Do not use the hose as a strength member to pull or lift the Weight ........164 lbs. (74.4 kg) equipment. • Do not lift by cart handle when loading or unloading. Maximum hose length ....300’ (91.4 m) © Titan Tool Inc. All rights reserved.

  • Page 4: Table Of Contents

    Safety Precautions section at the front of this a gasoline that contains alcohol, or one that you think contains alcohol, switch to a gasoline that manual before operating this equipment. you know does not contain alcohol. © Titan Tool Inc. All rights reserved.

  • Page 5: Setup

    NOTE: Make sure that the spray gun does not have a tip rapidly and firmly. or tip guard installed. Continue to hold the rope as you let it return. Pull and return the rope until the engine starts. © Titan Tool Inc. All rights reserved.

  • Page 6: Painting

    10. Turn the pressure control knob fully counterclockwise to position. its lowest setting. 7. Move the PRIME/SPRAY valve down to the PRIME 11. Turn off the sprayer by moving the sprayer ON/OFF switch position. to the OFF position. © Titan Tool Inc. All rights reserved.

  • Page 7: Spraying

    2. Remove the gun tip and tip guard and clean with a brush coverage. using the appropriate solvent. 3. Place the siphon tube into a container of the appropriate solvent (refer to recommendations of the material © Titan Tool Inc. All rights reserved.

  • Page 8: Maintenance

    Failure to for recommendations. do so may lead to a static electric 4. If you have any further questions concerning your TITAN discharge, which may cause a fire. airless sprayer, call TITAN: 15. Trigger the gun into the metal waste container until the Technical Service (U.S.) .......

  • Page 9: Replacing The Filter

    • Make sure to use a spark plug wrench when installing and removing the plug. Electrostatic discharge (ESD) potential could cause Replacing the Filter damage to electronic pressure control. use Titan ESD wrist strap P/N 0507958 or equivalent when 1. Loosen and remove the filter working on electronic pressure control.

  • Page 10: Replacing The Sprayer On/Off Switch

    Board the EPC housing. Tighten securely. housing. Gently move the assembly away from 22. Take the sprayer to a Titan Authorized Service Center for the sprayer and allow the re-calibration. assembly to hang from the housing. 23. After re-calibration, pressurize the system and check for 3.

  • Page 11: Replacing The Electronic Pressure Control (Epc) Assembly

    Fill the slider cup with Lubriplate 3000W grease (the slider cup is 8. Take the sprayer to a Titan Authorized Service Center for the area on the slider assembly where the connecting rod re-calibration.

  • Page 12: Replacing The Gears

    23. Using a 7/8” open-end wrench, attach the fluid hose to the Pump Housing fitting on the back of the fluid section. Tighten securely. Gear Assembly Front Cover Thick Thrust Washer Pump Housing Socket Screw Front Cover Screw © Titan Tool Inc. All rights reserved.

  • Page 13: Servicing The Clutch Assembly

    Hex Screw Electrostatic discharge (ESD) potential could cause Engine Shaft damage to electronic pressure control. use Titan ESD 8. Locate the clutch hub and armature assembly on the end wrist strap P/N 0507958 or equivalent when working of the engine shaft. Note the two set screws as well as on electronic pressure control.
  • Page 14 Clutch Field Wires Electrostatic discharge (ESD) potential could cause Lock Clutch Field damage to electronic pressure control. use Titan Washer Set Screw ESD wrist strap P/N 0507958 or equivalent when Clutch working on electronic pressure control.

  • Page 15: Servicing The Fluid Section

    Large Beveled Edge rest on the upper packing assembly. 33. Apply blue Loctite #242 to the threads of the upper seal retainer. Thread the upper seal retainer into the cylinder but do not tighten. © Titan Tool Inc. All rights reserved.
  • Page 16 When the connecting pin hole on the piston rod lines up with the hole in the slider assembly, insert the NOTE: Repacking kit P/N 0509940 is available. For best connecting pin. results use all parts supplied in this kit. © Titan Tool Inc. All rights reserved.

  • Page 17: Troubleshooting

    Turn the pressure control knob clockwise to supply power to the unit and increase the pressure setting. Faulty or loose wiring. Inspect or take to a Titan authorized service center. The gas tank is empty. Fill the gas tank. The unit will not prime.

  • Page 18: Français

    Il pourrait l’appareil. s’avérer nécessaire de consulter un plasticien ou un spécialiste • Ne pas pulvériser de produit sur la pompe. en chirurgie reconstructive de la main. Français © Titan Tool Inc. Tous droits réservés.
  • Page 19 électrique de la prise avant de travailler sur l’équipement. • N’utilisez pas le tuyau pour tirer ou soulever l’équipement. • Ne pas soulever par la poignée de chariot en chargeant ou en déchargeant. © Titan Tool Inc. Tous droits réservés. Français...

  • Page 20: Español

    Use la presión más baja posible para enjuagar el equipo. consultar con un cirujano plástico o un cirujano especialista en • No rocíe el ensamblaje de la bomba. reconstrucción de las manos. Español © Titan Tool Inc. Todos los derechos reservados.
  • Page 21 • No utilice la manguera como elemento de fuerza para tirar del equipo o levantarlo. • No levantar por la manija del carro al cargar o descargando. © Titan Tool Inc. Todos los derechos reservados. Español...

  • Page 22: Parts Listings

    0509521 Retaining ring ...........1 0509928 Grounding cable ........1 0509144 Fluid section assembly ......1 0507785 Return hose (not shown) ......1 0509651 Siphon tube ..........1 0507387 Hose, high pressure (not shown)....1 0507783 Hose clip ...........1 © Titan Tool Inc. All rights reserved.

  • Page 23: Drive Assembly

    Engine ............1 0509567 Drive shaft assembly ........1 0509569 Hex screw ..........4 0555902 Clutch field assembly........1 0507786 Lock washer ..........4 0507748 Cap ............1 NOTE: all electrical work should be performed by an authorized service center. © Titan Tool Inc. All rights reserved.

  • Page 24: Fluid Section Assembly

    NOTE: When repacking the fluid section, make sure the raised lip on the bottom of the lower packing is fully outside the packing around the piston rod after insertion of the piston rod. © Titan Tool Inc. All rights reserved.

  • Page 25: Cart Assembly

    Cart (includes item 10) ......1 0507737 Transducer ..........1 0509624 Wheel ............2 0509420 Plug, 3/8” ..........1 0088162 Outlet fitting, 3/8” x 1/4” ......1 0295697 Plug, 1/4” ..........1 0555625 Filter housing ..........1 0507690 PRIME/SPRAY valve assembly ....1 © Titan Tool Inc. All rights reserved.

  • Page 26: Prime/Spray Assembly

    Siphon hose..........1 5006536 Inlet screen ..........1 0507783 Clamp ............1 0509727 Swivel elbow ..........1 0509760 Adapter .............1 0509761 Hose clamp ..........1 0509788 Clip ............1 0509789 Spring ............1 55 Gallon Siphon Set (optional, P/N 0507977) © Titan Tool Inc. All rights reserved.

  • Page 27: Electrical Schematic

    Electrostatic discharge (ESD) wrist strap 9870307 Grease, 6 lb. can Labels Part # Description 0290802 Logo label, front 0295840 Warning label, explosion 0295841 Warning label, injection 0295805 Shock hazard label 0509819 “No Oil” label © Titan Tool Inc. All rights reserved.

  • Page 28: Limited Warranty

    Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or extended warranty published by Titan, Titan’s obligation under this warranty is limited to replacing or repairing without charge those parts which, to Titan’s...

This manual is also suitable for:

Advantage gpx 165050903905090550509059

Table of Contents