Titan ADVANTAGE GPX 165 Owner's Manual
  1. Manuals
  2. Brands
  3. Titan Manuals
  4. Power Pump
  5. ADVANTAGE GPX 165
  6. Owner's manual
Titan ADVANTAGE GPX 165 Owner's Manual

Titan ADVANTAGE GPX 165 Owner's Manual

Gas piston pump
Hide thumbs Also See for ADVANTAGE GPX 165:
Table of Contents

Advertisement

Quick Links

Download this manual
ADVANTAGE GPX 165
Model Numbers:
Bare
Complete
Bare w/5 Gal. Siphon
Complete w/5 Gal. SIphon
Gas Piston Pump
0509009
0509039
0509055
0509059
Owner's Manual
Notice d'utilisation
Manual del Propietario
Do not use this equipment before
reading this manual!
NOTE: This manual contains important
warnings and instructions. Please read
and retain for reference.
© Titan Tool Inc. All Rights Reserved. Form No. 0528902D
1114
•

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ADVANTAGE GPX 165 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Titan ADVANTAGE GPX 165

Summary of Contents for Titan ADVANTAGE GPX 165

  • Page 1 NOTE: This manual contains important Bare 0509009 warnings and instructions. Please read Complete 0509039 and retain for reference. Bare w/5 Gal. Siphon 0509055 Complete w/5 Gal. SIphon 0509059 © Titan Tool Inc. All Rights Reserved. Form No. 0528902D 1114 •...

  • Page 2: Safety Precautions

    A leak can inject material 3. Always use the nozzle tip guard. Do not spray without the into the skin. nozzle tip guard in place. English © Titan Tool Inc. All rights reserved.

  • Page 3: Table Of Contents

    To avoid severe burns or fire hazards, let the engine cool before transporting it or storing it indoors. 11. Never ship/transport unit with gasoline in the tank. English © Titan Tool Inc. All rights reserved.

  • Page 4: General Description

    Occasionally you may experience light spark knock while operating under heavy loads. This is no cause for concern, it simply means your engine is operating efficiently. English © Titan Tool Inc. All rights reserved.

  • Page 5: Preparing To Paint

    NOTE: Incompatible fluids and paint may cause the valves cleanup. to become stuck closed, which would require disassembly and cleaning of the sprayer’s fluid section. English © Titan Tool Inc. All rights reserved.

  • Page 6: Painting

    Try to keep the pressure control knob at the lowest setting that maintains good atomization. NOTE: Turning the pressure up higher than needed to atomize the paint will cause premature tip wear and additional overspray. English © Titan Tool Inc. All rights reserved.

  • Page 7: Spraying

    Approximately than in a fine spray. Paint tailing pattern 10 to 12 inches Right way Wrong way English © Titan Tool Inc. All rights reserved.

  • Page 8: Cleanup

    Always contact the supplier of solvents for recommendations. which may cause a fire. 4. If you have any further questions concerning your titan airless sprayer, call titan: 15. Trigger the gun into the metal waste container until the paint is flushed out of the hose and solvent is coming out of the gun.

  • Page 9: Maintaining The Engine

    • Make sure to use a spark plug wrench when installing and valve stem to secure the valve handle in position. removing the plug. Gasket Filter Valve Housing Housing Assembly Valve Stem Valve Handle Dowel Pin Cam Base Groove Pin English © Titan Tool Inc. All rights reserved.

  • Page 10: Replacing The Potentiometer

    Replacing the Sprayer ON/OFF Switch Electrostatic discharge (ESD) potential could cause Electrostatic discharge (ESD) potential could cause damage to electronic pressure control. use Titan ESD damage to electronic pressure control. use Titan ESD wrist strap P/N 0507958 or equivalent when working wrist strap P/N 0507958 or equivalent when working on electronic pressure control.

  • Page 11: Replacing The Electronic Pressure Control (Epc) Assembly

    Fitting 7. Install the four screws that secure the EPC assembly to the EPC housing. Tighten securely. 8. Take the sprayer to a Titan Authorized Service Center for re- Cart calibration. Filter Assembly Hex Screw Replacing the Slider Assembly and Slider Housing 14.

  • Page 12: Replacing The Gears

    When the connecting pin hole on the piston pump housing (refer to the “Replacing the Slider and rod lines up with the hole in the slider assembly, insert the Slider Housing” procedure in this section). connecting pin. English © Titan Tool Inc. All rights reserved.

  • Page 13: Servicing The Clutch Assembly

    7. Slide the pump and gear housings away from the engine to 16. Make sure the friction surface of the clutch armature is clean disengage them from the clutch housing. and free from oil or grease. English © Titan Tool Inc. All rights reserved.

  • Page 14: Shaft Assembly

    Electrostatic discharge (ESD) potential could cause 5. Line up the four holes around the outside of the clutch field damage to electronic pressure control. use Titan ESD with the four set screw holes in the gear housing. The clutch wrist strap P/N 0507958 or equivalent when working field wires should be at approximately the 1 or 2 o’clock...

  • Page 15: Servicing The Fluid Section

    28. Remove the piston rod from the vise. through the slider assembly and Cylinder piston. The connecting pin will fall 29. Clean the cylinder. Inspect the cylinder for damage and replace if necessary. English © Titan Tool Inc. All rights reserved.
  • Page 16 Tighten the inlet valve housing until the o-ring engages, then continue to tighten until snug. Once snug, torque to 300 in.-lbs. (25 ft.-lbs.). English © Titan Tool Inc. All rights reserved.

  • Page 17: Troubleshooting

    Turn the pressure control knob clockwise to supply power to the unit and increase the pressure setting. Faulty or loose wiring. Inspect or take to a Titan authorized service center. The gas tank is empty. Fill the gas tank. The unit will not prime.

  • Page 18: Français

    Il pourrait s’avérer nécessaire de consulter un plasticien ou un spécialiste en chirurgie reconstructive de la main. Français © Titan Tool Inc. Tous droits réservés.
  • Page 19 Pour éviter des brûlures graves ou des risques d’incendie, laissez le moteur refroidir avant de le transporter ou de le ranger à l’intérieur. • Ne transportez jamais le moteur si le réservoir est plein. Français © Titan Tool Inc. Tous droits réservés.

  • Page 20: Español

    La toxicidad es un factor a considerar con ciertos revestimientos inyectados directamente en la corriente sanguínea. Puede ser aconsejable consultar con un cirujano plástico o un cirujano especialista en reconstrucción de las manos. Español © Titan Tool Inc. Todos los derechos reservados.
  • Page 21 11. Nunca envíe ni transporte la unidad con gasolina en el tanque. 14. Desenchufe siempre el cable antes de trabajar en el equipo. ImPORTANTE: No cargue el equipo por el asa del carrito durante la carga y descarga. Español © Titan Tool Inc. Todos los derechos reservados.

  • Page 22: Parts Listings

    Wire harness 0509520 Connecting pin 0509553 Screw 0509521 Retaining ring 0509928 Grounding cable 0509144 Fluid section assembly 0507785 Return hose (not shown) 0509651 Siphon tube 0507387 Hose, high pressure (not shown) 0507783 Hose clip © Titan Tool Inc. All rights reserved.

  • Page 23: Drive Assembly

    Drive Assembly NOTE: All electrical work should be performed by a Titan authorized service center. Item Part No. Description qty. Item Part No. Description qty. 9850936 ON/OFF switch 0507740 Pressure control knob 0509558 Electronic pressure control assembly 0507749 Seal nut...

  • Page 24: Fluid Section Assembly

    NOTE: When repacking the fluid section, make sure the raised lip on the bottom of the lower packing is fully outside the packing around the piston rod after insertion of the piston rod. © Titan Tool Inc. All rights reserved.

  • Page 25: Cart Assembly

    0509386 Lock washer 0507737 Transducer 0295608 Screw 0509420 Plug, 3/8” 0555218 Cart (includes item 10) 0088162 Outlet fitting, 3/8” x 1/4” 0509624 Wheel 0295697 Plug, 1/4” 0555625 Filter housing 0507690 PRIME/SPRAY valve assembly © Titan Tool Inc. All rights reserved.

  • Page 26: Prime/Spray Assembly

    0507662 Valve handle 0507964 Return hose 0509185 Siphon hose 5006536 Inlet screen 0507783 Clamp 0509727 Swivel elbow 0509760 Adapter 0509761 Hose clamp 0509788 Clip 0509789 Spring 55 Gallon Siphon Set (optional, P/N 0507977) © Titan Tool Inc. All rights reserved.

  • Page 27: Electrical Schematic

    550-110 S-5 Spray Pack with 50’ x 1/4” airless hose 0295841 Warning label, injection 0295805 Shock hazard label 0507958 Electrostatic discharge (ESD) wrist strap 0509819 “No Oil” label 9870307 Grease, 6 lb. can © Titan Tool Inc. All rights reserved.

  • Page 28: Limited Warranty

    Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or extended warranty published by Titan, Titan’s obligation under this warranty is limited to replacing or repairing without charge those parts which, to Titan’s reasonable satisfaction, are...

Table of Contents