Table of Contents
Advertisement
Quick Links
Industrial Conveyor Specialists
Installation, Maintenance & Parts Manual
For
MODEL 490
V-Belt Driven Live Roller Curve Conveyor
For Additional copies of this manual, please visit our website at
www.titanconveyors.com
Go to Info Center, Select the Maintenance Manual Tab
and select the manual for your model conveyor
or click on the link below.
https://www.titanconveyors.com/info-center#823236-maintenance-manuals
Titan Conveyors
735 Industrial Loop Road
New London, WI 54961
920-982-6600
800-558-3616
FAX 920-982-7750
E-mail: sales@titanconveyors.com
Website: www.titanconveyors.com
Serial No.
Go to Table of Contents
Advertisement
Table of Contents
Related Manuals for Titan 490
Summary of Contents for Titan 490
- Page 1 Industrial Conveyor Specialists Installation, Maintenance & Parts Manual MODEL 490 V-Belt Driven Live Roller Curve Conveyor For Additional copies of this manual, please visit our website at www.titanconveyors.com Go to Info Center, Select the Maintenance Manual Tab and select the manual for your model conveyor or click on the link below.
- Page 2 Page 11 ..............Model 490 Blow Apart Drawing (A) Seller warrants that the material in and the workmanship on the equipment manufactured by TITAN will be free from defects at time of shipment. If during the first year from the date of shipment, the Buyer establishes to the seller’s satisfaction that any part or parts manu- factured by TITAN were defective at the time of shipment, TITAN will, at its own expense, repair or replace (but not install) replacement parts.
- Page 3 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
-
Page 4: Installation
Titan at 920-982-6600. I. RECEIVING Upon delivery of your Titan conveyor, check the packing slip or bill of lading accompanying the unit. If any components are missing, contact Titan IMMEDIATELY with a description of the missing components along with the conveyor serial number(s). -
Page 5: Frame Assembly
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S... -
Page 6: Component Checklist
MODEL 490 BELT INSTALLATION BELT LOCATION The drive belt on Model 490 conveyors comes installed from the factory. The typical belt threading arrangement is pictured in FIGURE 3 BELOW. FIGURE 3 After making sure the conveyor is cleared off and the drive pulley is moving the belt in the correct direction,run the conveyor. -
Page 7: Maintenance
2. VENTILATION - During normal operation gear reducers build up heat and pressure that MUST be vented to protect the seals and gears. If not installed at Titan, a brass vent plug contained in a small plastic bag, will be put in a box or larger bag along with fasteners sent loose for use during field installation. - Page 8 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
-
Page 9: Heavy Duty
ONLY compatible polyglycol lubricants should be used. Contact the factory for more information. TEMPERATURE - Most Titan Units are supplied with wormgear reducers. These units may run at temperatures between 100 degrees to 200 degrees F. (Higher temperatures are especially common during start up). There is NO NEED TO WORRY unless temperatures exceed 200 degrees F. -
Page 10: Recommended Oil
SAE 40 120 degrees - 140 degrees F SAE 50 REMEMBER - ALL GUARDS AND BOTTOM PANS, IF PROVIDED, MUST BE REPLACED BEFORE RUNNING CONVEYOR. TITAN INDUSTRIES IS NOT DANGER RESPONSIBLE FOR INJURIES CAUSED BY NOT COMPLYING WITH SAFETY INSTRUCTIONS. - Page 11 V E Y O R S V E Y O R S V E Y O R S V E Y O R S MODEL 490 V-BELT DRIVEN LIVE ROLLER CURVE CONVEYOR OPTIONAL TOP MT. DRIVE 25 26 1. FRAME WELDMENT...