Connect Programming Cable - Rabbit RabbitCore RCM3000 User Manual

2.2.2 Connect Programming Cable

The programming cable connects the RCM3000 module to the PC running Dynamic C to
download programs and to monitor the module for debugging.
Connect the 10-pin connector of the programming cable labeled
the RCM3000 module as shown in Figure 2. Be sure to orient the marked (usually red)
edge of the cable towards pin 1 of the connector. (Do not use the
used for a normal serial connection.)
NOTE: Be sure to use the programming cable (part number 101-0513) supplied with this
Development Kit—the programming cable has red shrink wrap around the RS-232 con-
verter section located in the middle of the cable. Programming cables with blue or clear
shrink wrap from other from other Rabbit Semiconductor kits were not designed to work
with RCM3000 modules.
RN1
GND
NC PD1 PD0
GND +3.3V PD7 PD6
VBAT
VRAM PD3 PD2
EXT
/RES
SM1 PD5 PD4
IN
SM0
/IORD PG3 PG2
/IOWR PG4 PG1 PG0
PG5 PG6
PC7 PC6
PG7 PE0 PC5 PC4
PE1 PE3
PC3 PC2
PE4 PE5 PC1 PC0
PE6 PE7
PF0 PF1
PF7 PF6 PF2 PF3
PF5 PF4
PA0 PA1
PB7 PB6 PA2 PA3
PB5 PB4
PA4 PA5
PB3 PB2 PA6 PA7
PB0 /RES
STAT GND
J3
J1
RN2
C1
C2
R1
R4
R5
IR1 R2
RC13
RC12
R21
RC10
RC11
GND NC PD1 PD0
GND +3.3V PD7 PD6
VBAT
VRAM PD3 PD2
EXT
/RES
SM1 PD5 PD4
IN
SM0 /IORD PG3 PG2
/IOWR PG4 PG1 PG0
PG5 PG6 PD4 PD5
PG7 PE0 PC5 PC4
PE1 PE3 PC3 PC2
PE4 PE5 PC1 PC0
PE6 PE7 PF0 PF1
PF7 PF6 PF2 PF3
PF5 PF4 PA0 PA1
PB7 PB6 PA2 PA3
PB5 PB4 PA4 PA5
PB3 PB2 PA6 PA7
PB0 /RES STATUS GND
J2 J4
Figure 2. Connect Programming Cable to RCM3000
Connect the other end of the programming cable to a COM port on your PC.
NOTE: Some PCs now come equipped only with a USB port. It may be possible to use
an RS-232/USB converter with the programming cable supplied with your RabbitCore
module. An RS-232/USB converter is available through the Web store. Note that not all
RS-232/USB converters work with Dynamic C.
User's Manual
TP2
GND/EGND
RCM1JB
RCM1JA RN3
RCM3000 ETHERNET CORE MODULE
RN4
SLAVE
UX11
UX10
RC18
MASTER
RC15
RCM2
RC19
RC24
RC20
RC23
UX9
C3
RC14
RC17
RC22
RC16
RC21
UX3
R7 R9 R11 R13
RC2
RC3
UX2
GND/EGND
RCM3000 ETHERNET CORE MODULE
TP1
R15 R16
R14
U1
C5
C8
RCM2JA RCM2JB
C6
C4
RESET
1 C7 1 3
3 3 1
RxC TxC
J5
2 4 2 4 2 4
S1 S2 S3
TxB RxB GND
RN5 DS3
R20
C13
HOT
R17
U4
C12
+5V
Battery
+3.3V
BT1
GND GND
GND
+5V
+3.3V +3.3V
J8
+3.3V +3.3V
+5V
+5V
RC6 RC7
UX6
C16
U6
C9
To
U2
UX5
PC COM port
RC8 RC9
UX8 UX7
Colored
RCM30/31/32XX SERIES
R18 R19
PROTOTYPING BOARD
shrink wrap
PG6 PG7
Colored edge J10
DS2
DS1
DISPLAY BOARD
Programming Cable
PROG to header J3 on
connector, which is
DIAG
C15
L1
C17
J11
D1
C10
C11
2.5 mm JACK
D2
GND
+DC
U5
+5V
+3.3V
GND
+5V
UX4 UX12
RC25
RC4 RC5
DISPLAY BOARD
RC27
C14
RC28
U3
RC29
RC26
UX13
J7
DISPLAY BOARD
7