Table of Contents
Advertisement
Quick Links
6BSE-LDS
6BSE-HLDS
9, 12, 18, 24 & 30 HP @ 1150 RPM
18, 24, 30, 36, 48 & 60 HP @ 1750 RPM
barmesapumps.com
IMPORTANT! - Read all instructions in this manual before operating or servicing
a pump.
6BSE-LDS
9-30 HP
18-60 HP
Installation, Operation &
Maintenance Manual
Submersible Solids
Handling Pumps
6BSE-HLDS
30-60 HP
Last update: 08/07/2020
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Barmesa Pumps 6BSE9036LDS
Summary of Contents for Barmesa Pumps 6BSE9036LDS
- Page 1 Installation, Operation & Maintenance Manual Submersible Solids Handling Pumps 6BSE-LDS 6BSE-HLDS 9, 12, 18, 24 & 30 HP @ 1150 RPM 18, 24, 30, 36, 48 & 60 HP @ 1750 RPM barmesapumps.com 6BSE-LDS 9-30 HP 6BSE-HLDS 18-60 HP 30-60 HP IMPORTANT! - Read all instructions in this manual before operating or servicing a pump.
-
Page 2: General Safety Information
IMPORTANT! - Barmesa Pumps is not systems, that are required to reduce installations where there is responsible for losses, injury or the potencial for property damage. -
Page 3: Specifications
NEMA CORD CORD LOCKED CORD WEIGHT MODEL HP VOLTS PHASE (Nominal) AMPS ROTOR AMPS CODE SIZE TYPE O. D. (pounds) 6BSE9036LDS 1150 1.34" 6BSE9046LDS 1150 1.34" 6BSE12036LDS 12 1150 1.34" 6BSE12046LDS 12 1150 1.34" 6BSE18036LDS 18 1150 1.34" 6BSE18046LDS 18 1150 1.34"... -
Page 4: Specifications And Dimensions
Specifications & Dimensions NEMA CORD CORD LOCKED CORD WEIGHT MODEL HP VOLTS PHASE ROTOR AMPS O. D. (pounds) (Nominal) AMPS CODE SIZE TYPE 6BSE30034HLDS 30 1750 1.34" 6BSE30044HLDS 30 1750 1.34" 6BSE36034HLDS 36 1750 1.34" 6BSE36044HLDS 36 1750 1.34" 6BSE48044HLDS 48 1750 1.34"... -
Page 5: Recommendations And Warnings
Recommendations and Warnings 4Receiving inspection 4 Installation 4Liquid Level Controls Upon receiving the pump, it should These pumps are recommended for The level control(s) should be inspected damage use in a sump, basin or lift station. mounted on the discharge piping, a shortages. -
Page 6: Installation & Service
Installation & Service These situations ma y induce a false IMPORTANT! - The overload will then signal in the moisture etecting automatically reset and start the circuit. If none of the above test pump up after the motor cools to a prove conclusive, the pump(s) should safe temperature. - Page 7 Service a) Inspect motor chamber for oil If oil is found to be clean and Use soap solution around the sealed Ÿ level and contamination. uncontaminated (measuring areas above the oil level and nspect b) Inspect impeller and body for above 15 V breakdown), re ill joints for "air bubbles".
- Page 8 Service 4Disassembly Apply adhesive compound to the Motor and Bearings - Remove Impeller and Volute - Disconnect shaft and press bearing (1 ) onto volute, impeller, seal plate and seal as power. Remove hex nuts ( ) and previously stated and drain oil from shaft, position squarely onto the vertically lift motor housing and seal shaft applying force to the inner race...
- Page 9 Service Thread cap screws (25) into bearing housing (15) and tighten. Refill chamber with oil. Conduit Box Assembly - Check power (38) and control cables (39) for crackes or damage and replace complete conduit box (4) if required. (See Figure 4) Bring motor wires through opening in top of motor housing (3), check sleeving and replace if damaged.
- Page 10 Service Wear Ring Apply retaining compound to the bore of volute (37) and press wear ring (33) into bore until seated. Impeller and Volute - Install impeller (32) by appling a thin film of oil to motor shaft and slide impeller straight onto shaft, keeping keyways lined up.
- Page 11 Repair Parts Figure 6 barmesapumps.com VOLUTE FOR 6BSE-HLDS For Repair Part Please supply: Model Number and Serial as shown on Name Plate, and Part Description and Part Number as shown on Parts List.
- Page 12 Parts List 46BSE-LDS barmesapumps.com 30400423 For Repair Part Please supply: Model Number and Serial as shown on Name Plate, and Part Description and Part Number as shown on Parts List.
- Page 13 Parts List 46BSE-HLDS barmesapumps.com 30400423 For Repair Part Please supply: Model Number and Serial as shown on Name Plate, and Part Description and Part Number as shown on Parts List.
-
Page 14: Troubleshooting Chart
13. Piping attachments to building structure too loose or rigid NOTE: Barmesa Pumps assumes no responsibility for damage or injury due to disassembly in the field. Disassembly of the pumps or supplied accessories other than at Barmesa Pumps or its authorized service centers, automatically voids warranty.
Need help?
Do you have a question about the 6BSE9036LDS and is the answer not in the manual?
Questions and answers