Video passport
1ru multi-path video converter, frame synchronizer and decoder (91 pages)
Summary of Contents for evertz 2405EO
Page 1
Fiber Converter. All rights reserved. No part of this publication may be reproduced without the express written permission of Evertz Microsystems Ltd. Copies of this guide can be ordered from your Evertz products dealer or from Evertz Microsystems.
Page 2
WARNING Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could void the user’s authority to operate the equipment. Use of unshielded plugs or cables may cause radiation interference. Properly shielded interface cables...
Page 3
Jun 08 Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for the rights of third parties, which may be effected in any way by the use thereof. Any representations in this document concerning performance of Evertz products are for informational use only and are not warranties of future performance, either express or implied.
Page 4
2400 Series Fiber Converter Manual 2405EO SMPTE259M Re-Clocking Electrical to Fiber Converter This page left intentionally blank Revision 2.1...
The 2405EO converter features one auto-equalized coaxial input with two reclocked serial digital outputs and one reclocked fiber output. The 2405EO has been designed to be used primarily as a reclocking SMPTE 259M or DVB-ASI distribution amplifier and converter, however SMPTE 310M (19.4 Mb/s) signals can also be reclocked.
2400 Series Fiber Converter Manual 2405EO SMPTE259M Re-Clocking Electrical to Fiber Converter Cable Drivers Active 2 Serial Signal Carrier Video BNC Outputs (1 is DVB-ASI Reclocker Equalizer compliant) SMPTE 310M Optical Reclocker Signal Driver Optical Weak Output 259M/310M Laser Fault...
2400 Series Fiber Converter Manual 2405EO SMPTE259M Re-Clocking Electrical to Fiber Converter INSTALLATION The 2405EO is a compact module that has three BNC connectors and one SC/PC (shown), ST/PC or FC/PC optical connector. Figure 2-1: 2405EO Module SDI INPUT: Input BNC connector for 10-bit serial digital video signals compatible with the SMPTE 259M, DVB-ASI or SMPTE 310M standard.
Background colour: yellow Triangular band: black Symbol: black The laser modules used in the Evertz fiber optic modules are Class I, with a maximum output power of 2mW, and wavelengths of either 1310 nm or 1470 nm to 1610 nm. 2.1.2. Assembly Assembly or repair of the laser sub-module is done only at Evertz facility and performed only by Evertz technical personnel.
2400 Series Fiber Converter Manual 2405EO SMPTE259M Re-Clocking Electrical to Fiber Converter Figure 2-2: Typical 2405EO Certification and Identification Label (Serial # and bar code differ from unit to unit) 2405EO-5 Revision 2.1...
5 cm to avoid fiber-bending loss that will decrease the maximum attainable distance of the fiber cable. The Evertz fiber optic modules come with cable lockout devices, to prevent the user from damaging the fiber by installing a module into a slot in the frame that does not have a suitable I/O module.
2400 Series Fiber Converter Manual 2405EO SMPTE259M Re-Clocking Electrical to Fiber Converter 3.4. ELECTRICAL Voltage: + 12VDC Power: 6 Watts EMI/RFI: Complies with FCC regulations for class A devices Complies with EU EMC directive DC Power Supply: 115/230 VAC 50/60 Hz, 30 VA 3.5.
2400 Series Fiber Converter Manual 2405EO SMPTE259M Re-Clocking Electrical to Fiber Converter STATUS LEDS ACTIVE SIGNAL: This Green LED will be On when there is a valid signal present at the module input. NO CARRIER: This Red LED will be On when there is no valid signal present at the module input.
USER CONTROLS The 2405EO is equipped with a 4 position DIP switch to allow the user to configure the module. The On position is down, or closest to the printed circuit board. Table 5-1 gives an overview of the DIP switch functions.