Specifications - Toro REELMASTER 6700-D Operator's Manual

Specifications

Engine: Peugeot, 4-cylinder, 4-cycle, overhead cam,
116 cu. in (1.9 liter) displacement liquid-cooled diesel
engine. 42 hp (31 kW); governed to 2750 rpm high idle;
23.5:1 compression ratio, 3.27" (83 mm) bore x 3.46"
(88 mm) stroke. Automatic glow plug/starter interlock
system. Heavy-duty, 2-stage, remote air cleaner.
Main Frame: All-welded formed steel frame, includes
tie-down loops.
Cooling System: Rear-mounted, cross-flow agricultural
type radiator; 7 fins per inch. 7.1 liter capacity. Air to
oil cooler mounted to the rear of the radiator tips out-
ward for cleaning. Removable oil cooler/radiator
screen.
Fuel System: Rotary fuel injection pump with ener-
gized-to-run (ETR) fuel flow solenoid. Replaceable
spin-on fuel filter/water separator with water sensor.
Fuel capacity: 64 liter.
Traction System: Servo-controlled hydrostatic system
driving double-planetary, gear-reduction, front-wheel
drives. Foot pedal control of forward/reverse ground
speed.
Toro 4-MaticR 4-Wheel Drive System only: Rear
drive axle coupled to hydrostatic transmission via an
overrunning clutch for full-time, on-demand 4-wheel
drive. A Roll Over Protective Structure and seat belt are
standard.
Ground Speed: 0–16 kmh forward; 0–6 kmh reverse.
Cutting Unit Drive System: Reel motors feature quick
disconnect for removal or installation onto the cutting
unit. Cutting units can be driven from either end.
Seat: Deluxe high-back suspension seat with adjustable
fore and aft travel, weight and height. Tool box at the
left side of the seat.
Steering System: Power steering with dedicated power
source.
Tires: Two rear steering tires: 20 x 10.00–10, tubeless,
6-ply rating. Two front traction drive tires: 29 x
12.00–15 tubeless, 6-ply rating. Recommended tire
pressure for front and rear tires is 103–138 kPa.
Brakes: Individual totally enclosed, multi-disc, wet
brakes and parking brakes on front traction wheels.
Hydrostatic braking through traction drive.
Electrical Features: 12-volt, 530 cold-cranking
amperes at 0° F (–18° C), 85-minute reserve capacity
at 80° F (27° C), maintenance-free battery. 55-amp
alternator with l° C regulator/rectifier. Automotive-type
electrical system. Seat switch, reel and traction inter-
lock switches.
Controls: Foot-operated traction and brake pedals.
Hand operated throttle, speed control lever, parking
brake lock, ignition switch with automatic preheat
cycle, single joy stick control for cutting unit on/off
and lift lower. Cutting unit backlap switch under the
operator's seat. Height-of-cut selector knob located
under the control panel.
Gauges: Hour meter, speedometer, fuel gauge, temper-
ature gauge, 4-bank warning lamp: oil pressure, water
temperature, amps, and glow plug. 2-bank warning
lamp: water in fuel, water level.
Diagnostics; The Automatic Control Electronics,
ACET system allows precise timing and control of
machine functions for maximum reliability. Toro stan-
dard diagnostic display connects to an electronic con-
trol unit to pinpoint any electrical problems quickly
and easily. Available DATA LOGT system allows
mechanic to find intermittent problems.
General Specifications (approx.):
Width-of-Cut:
Overall Width:
Transport
Operational
Overall Length:
Height:
Without roll-over protection system installed: 152
cm
With roll-over protection system
installed:
Weight:
*With 5-Blade Cutting Units & full fluid levels
338 cm
213 cm
373 cm
305 cm
213 cm
1,474 kg*
9