Summary of Contents for Horizon Hobby E-FLITE Viper 70mm EDF
Page 1
Scan the QR code and select the Manuals and Support quick links from the product page for the most up-to-date manual information. Scannen Sie den QR-Code und wählen Sie auf der Produktseite Instruction Manual die Quicklinks Handbücher und Unterstützung, um die aktuellsten Informationen zu Handbücher.
Page 2
This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance.
Registration Specifications Wingspan 43.31" (1100mm) Register your product today to join our mailing list and keep up to date with product updates, offers and E-flite news. ® Length 40.39" (1026mm) Without Battery: 47 oz (1340g) Weight With Recommended 6S 3200mAh Battery: 64 oz (1820g) Included Equipment Spektrum AR631 DSMX 6-Channel AS3X &...
Model Assembly Horizontal Stabilizer Installation 1. Connect both elevator servo connectors to the extensions labeled ELEV in the fuselage. Feed the excess servo wire into the fuselage, making sure the servo plugs and excess wire are not visible when looking in the tail cone. TIP: Note the correct polarity of the servo plugs: brown to brown, yellow to yellow, and,orange to orange.
Model Assembly Wing Installation 1. Carefully separate the aileron, flap, and retract servo extensions exiting the wing. 2. Ensure the servo plugs are securely connected to the Y-harness. The extensions are labeled AIL, FLAP, and GEAR. NOTE: The gear Y-harness is pre-installed. GEAR servo plugs will be installed after wing is installed.
Transmitter Setup Dual Rates IMPORTANT: After you set up your model, always rebind the transmitter and receiver to set the desired failsafe positions. Attempt your first flights in low rate. For landings, use high rate elevator. The GEAR Channel (CH 5) controls the retractable landing gear. If you are using a 6 NOTICE: To ensure AS3X technology functions properly, do not lower rate values channel transmitter, The FLAP Channel (CH 6) can be used to toggle SAFE Select.
General Binding Tips and Failsafe • The included receiver has been specifically programmed for operation of this • Once bound, the receiver will retain its bind settings for that transmitter until aircraft. Refer to the receiver manual for correct setup if the receiver is replaced. you re-bind.
SAFE Select Technology ® When flying in SAFE Select mode the aircraft will return to level flight any time the deviations. With SAFE Select, holding deliberate control inputs will command the aileron and elevator controls are at neutral. Applying aileron or elevator control will aircraft to fly at a specific angle and the model will make all corrections to maintain cause the airplane to bank, climb or dive, and the amount the stick is moved will that flight attitude.
Battery Installation and ESC Arming Battery Selection We recommend a 22.2V 6S 3200mAh 50C LiPo battery with IC5 connector. If using a different battery, the battery should be of similar capacity, dimensions and weight to fit in the fuselage. Always be sure the model balances at the recommended CG with the battery chosen.
If the control surfaces do not respond as shown, DO NOT FLY. Refer to the Troubleshooting Guide for more information. If you need more assistance, contact the appropriate Horizon Hobby Product Support department. 1. Power on the transmitter. 2. Enable the throttle cut.
Control Surface Centering After assembly and transmitter setup, confirm that the control surfaces are centered. If the control surfaces are not centered, mechanically center the control surfaces by adjusting the linkages. If adjustment is required, turn the ball link on the linkage to change the length of the linkage between the servo arm and the control horn.
Troubleshooting Guide AS3X Problem Possible Cause Solution Damaged rotor or spinner Replace rotor or spinner Imbalanced rotor Balance the rotor Motor vibration Replace parts or correctly align all parts and tighten fasteners as needed Oscillation Loose receiver Align and secure receiver in fuselage Loose aircraft controls Tighten or otherwise secure parts (servo, arm, linkage, horn and control surface) Worn parts...
Replacement Parts Part Number Description Part Number Description EFL077501 Wing Set EFL7714 Screw Set EFL077502 Vertical Stabilizer EFLA7012DF 70mm Ducted Fan EFL077503 Horizontal Stabilizer EFLG130 Nose Gear 90 Degree Electric Retract EFL077504 Soft Tire Set EFLG131 Main Gear 90 Degree Electric Retract EFL077505 Decal Sheet EFLG077511...
Product, (iv) attempted service by anyone other Service Request submission process found on our website or call Horizon to obtain a than a Horizon Hobby authorized service center, (v) Product not purchased from an au- Return Merchandise Authorization (RMA) number. Pack the Product securely using a thorized Horizon dealer, (vi) Product not compliant with applicable technical regulations, shipping carton.
EU Manufacturer of Record: EFL Smart Viper 70mm EDF BNF-Basic (EFL077500): Hereby, Horizon Hobby, LLC Horizon Hobby, LLC declares that the device is in compliance with the 2904 Research Road following: EU Radio Equipment Directive 2014/53/EU, RoHS 2 Directive Champaign, IL 61822 USA 2011/65/EU, RoHS 3 Directive - Amending 2011/65/EU Annex II 2015/863.
Page 16
E-flite, AS3X, DSM, DSM2, DSMX, EC5, IC5, Avian, Spektrum Airware, Bind-N-Fly, BNF, the Bind-N-Fly logo, SAFE, the SAFE logo, ModelMatch, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Need help?
Do you have a question about the E-FLITE Viper 70mm EDF and is the answer not in the manual?
Questions and answers