Horizon Hobby BLADE Fusion 180 Instruction Manual
Horizon Hobby BLADE Fusion 180 Instruction Manual

Horizon Hobby BLADE Fusion 180 Instruction Manual

Hide thumbs Also See for BLADE Fusion 180:

Advertisement

Quick Links

180
180
TM
Instruction Manual
Bedienungsanleitung
Manuel d'utilisation
Manuale di Istruzioni

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BLADE Fusion 180 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Horizon Hobby BLADE Fusion 180

  • Page 1 Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni...
  • Page 2: Safety Precautions And Warnings

    WARNING AGAINST COUNTERFEIT PRODUCTS: If you ever need to replace a Spektrum component found in a Horizon Hobby product, always purchase from Horizon Hobby, LLC or a Horizon Hobby authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum technology.
  • Page 3: Table Of Contents

    Adjusting the Gain Values ........12 Table of Contents ...........3 Saving the Gain Adjustments .......13 First Flight Preparation ...........4 Blade Fusion 180 Servo Adjustment .....13 Flying Checklist .............4 Entering Servo Adjustment Mode ......13 Transmitter Setup ..........4 Adjusting the Servo Neutral Position ....14 Installing the Flight Battery ........6...
  • Page 4: First Flight Preparation

    First Flight Preparation Flying Checklist • Remove and inspect contents ❏ Always turn the transmitter on fi rst • Begin charging the fl ight battery ❏ Plug the fl ight battery into the lead from the ESC • Install the fl ight battery in the helicopter ❏...
  • Page 5 DX7s, DX8 SYSTEM SETUP FUNCTION LIST Model Type Servo Setup Chan Travel Reverse Chan Travel Reverse HELI 100/110 Normal 100/100 Normal Swash Type 100/100 Normal 100/100 Normal 1 servo Normal 100/100 Normal 100/100 Normal F-Mode Setup 100/100 Normal Flight Mode F Mode D/R &...
  • Page 6: Installing The Flight Battery

    Installing the Flight Battery 1. Lower the throttle. CAUTION: Always keep the power lead positioned AWAY from the elevator servo. Failure to do so 2. Power on the transmitter. could cause the lead to get caught in the servo arm, which 3.
  • Page 7: Transmitter And Receiver Binding

    Transmitter and Receiver Binding ® ® Binding is the process of programming the receiver to Spektrum™ DSM2 /DSMX technology equipped aircraft recognize the GUID (Globally Unique Identifi er) code of a transmitter to the receiver for proper operation. single specifi c transmitter. You need to ‘bind’ your chosen Binding Procedure 1.
  • Page 8 Rudder Collective Pitch Side View Side View Motor Control Test Place the helicopter outdoors on a clean, fl at and level 3. Set the transmitter to normal fl ight mode. Ensure surface (concrete or asphalt) free of obstructions. Always the throttle is lowered completely. Turn throttle hold stay clear of moving rotor blades.
  • Page 9: Blade Fusion 180 Pre-Flight Checklist

    St unt 1 Mode: This mode has a constant moderate head speed and full range of rotor collective pitch available. The Blade Fusion 180 is intended to be fl own outdoors or St unt 2 Mode: This mode has a constant high head speed inside a large gymnasium.
  • Page 10: Low Voltage Cutoff (Lvc)

    Low Voltage Cutoff (LVC) Once the battery reaches 9V under load, the ESC will Repeatedly fl ying the helicopter until LVC activates will continuously lower power supplied to the motor until damage the helicopter battery. complete shutdown occurs. This helps prevent over- Disconnect and remove the Li-Po battery from the aircraft discharge of the Li-Po battery.
  • Page 11: Advanced Settings

    Advanced Settings The Fusion 180 default settings are appropriate for most users. We recommend fl ying with the default parameters before making any adjustments. WARNING: To ensure your safety, always disconnect the motor wires from the ESC before performing the following steps.
  • Page 12: Entering Gain Adjustment Mode

    Entering Gain Adjustment Mode DX6, DX6e and DX6i Users: DX7s, DX7 (G2), DX8, DX8 (G2), DX9, DX18 and DX20 Users: 1. Lower the throttle stick to the lowest position. 1. Lower the throttle stick to the lowest position. 2. Power ON the transmitter. 2.
  • Page 13: Saving The Gain Adjustments

    Blade Fusion 180 Servo Adjustment Your Blade Fusion 180 was setup at the factory and test fl own. The servo adjustment steps are usually only necessary in special circumstances, such as after a crash or if a servo or linkage is replaced.
  • Page 14: Adjusting The Servo Neutral Position

    Adjusting the Servo Neutral Position With the model in Servo Adjustment Mode, the control stick Once the servo you wish to adjust is selected, move the and gyro inputs are disabled and the servos are held in the cyclic stick forward or backward to adjust the servo neutral neutral position.
  • Page 15: Blade Fusion 180 Troubleshooting Guide

    Blade Fusion 180 Troubleshooting Guide Problem Possible Cause Solution Low fl ight battery or transmitter bat- Fully charge or replace the fl ight battery and/or transmit- tery voltage ter batteries Make sure the bind plug is connected to the receiver...
  • Page 16: Exploded View

    Exploded View...
  • Page 17: Replacement Parts

    Product, (iv) attempted service by anyone other and all Product(s) involved in a warranty claim. Service or than a Horizon Hobby authorized service center, (v) Product not replacement decisions are at the sole discretion of Horizon.
  • Page 18 Limitation of Liability withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, lost or damaged parcels, as Horizon is not responsible for INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF merchandise until it arrives and is accepted at our facility.
  • Page 19: Warranty And Service Contact Information

    Sales 800-338-4639 Horizon Technischer Service service@horizonhobby.de Hanskampring 9 European Union D 22885 Barsbüttel, Germany Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100 FCC Information FCC ID: BRWDASRX14 Supplier’s Declaration of Conformity Fusion 180 – BLH5850 Contains IC: 6157 A-AMRX14...
  • Page 20: Ic Information

    Compliance Information for the European Union EU Compliance Statement: BLH5850 Horizon Hobby, LLC  hereby declares that this product is in compli- ance with the essential requirements and other relevant provisions of the RED Directive.
  • Page 21 Blade, E-fl ite, Prophet, AS3X, DSM, DSM2, DSMX, Spektrum AirWare, ModelMatch, BNF, the BNF logo and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.

This manual is also suitable for:

Blh5850

Table of Contents