Titan 680 Installation, Maintenance, And Parts Manual
  1. Manuals
  2. Brands
  3. Titan Manuals
  4. Industrial Equipment
  5. 680
  6. Installation, maintenance, and parts manual
Titan 680 Installation, Maintenance, And Parts Manual

Titan 680 Installation, Maintenance, And Parts Manual

Multi-strand chain conveyor
Hide thumbs Also See for 680:
Table of Contents

Advertisement

Quick Links

Download this manual
TITAN INDUSTRIES
735 INDUSTRIAL LOOP ROAD
NEW LONDON WI 54961
920-982-6600
800-558-3616 Toll Free
920-982-7750 FAX
E-MAIL: sales@titanconveyors.com
Website: www.titanconveyors.com
MODEL 680
Multi-Strand Chain Conveyor
INSTALLATION, MAINTENANCE AND
PARTS MANUAL
For additional copies of this manual,
please visit our website at
www.titanconveyors.com.
Go to Replacement Parts/Accessories
and select Maintenance Manuals. You can then
select the manual for your model conveyor.
SERIAL NO.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 680 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Titan 680

Summary of Contents for Titan 680

  • Page 1 735 INDUSTRIAL LOOP ROAD NEW LONDON WI 54961 920-982-6600 800-558-3616 Toll Free 920-982-7750 FAX E-MAIL: sales@titanconveyors.com Website: www.titanconveyors.com MODEL 680 Multi-Strand Chain Conveyor INSTALLATION, MAINTENANCE AND PARTS MANUAL For additional copies of this manual, please visit our website at www.titanconveyors.com.
  • Page 2 (D) No representative of TITAN has been conferred with any authority to waive, alter, vary or add to the terms of warranty state herein, without prior authorization in writing executed by an officer of the company.

  • Page 3: Table Of Contents

    This will require you to call a Titan salesperson prior to your sending back the item to get a RGA number and receive instructions on how to return the item. Other information needed at this time would be your original purchase order number, Titan serial number, job number or invoice number.
  • Page 4 Safety The Safety alert symbol is used with the signal words DANGER, WARNING and CAUTION to alert you to safety messages. They are used in safety decals on the unit and with proper operation and procedures in this manual. They alert you to the existence and relative degree of hazards. Understand the safety message.

  • Page 5: Introduction

    Titan at 920-982-6600. I. RECEIVING Upon delivery of your Titan conveyor, check the packing slip or bill of lading accompanying the unit. If any components are missing, contact Titan IMMEDIATELY with a description of the missing components along with the conveyor serial number(s).

  • Page 6: Component Checklist

    COMPONENT CHECKLIST Prior to start up use the following list to double check the conveyor components. MOTOR Have a qualified electrician ensure the motor is wired correctly for your power source. Check that motor is securely fastened to the reducer or motorbase.

  • Page 7: Reducers

    2. VENTILATION - During normal operation gear reducers build up heat and pressure that MUST be vented to protect the seals and gears. If not installed at Titan, a brass vent plug contained in a small plastic bag, will be put in a box or larger bag along with fasteners sent loose for use during field installation. Remove the top most drain plug (refer to FIGURE 3) for the position of your reducer) and install the vent plug securely in place.
  • Page 8 ONLY compatible polyglycol lubricants should be used. Contact the factory for more information. TEMPERATURE - Most Titan Units are supplied with wormgear reducers. These units may run at temperatures between 100 degrees to 200 degrees F. (Higher temperatures are especially common during start up).

  • Page 9: Bearings

    BEARINGS 1. LUBRICATION - Bearings used on Titan Conveyors are normally pre-lubed for life. If customer requested, re-lube bearings are provided, the use of a #2 consistency lithium based grease is advised. Greasing Frequency should be as many times as necessary to maintain a small film of grease leaking at the seals.
  • Page 10 Model 680 Multi-Strand Chain Conveyor DRIVE SHAFT 16. FRAME SPREADER CHAIN 17. FRAME WELDMENT R/H DRIVE CHAIN SPROCKET 18. MOTORBASE 4 BOLT DRIVE BEARING 19. REDUCER TAKE-UP BRACKET FRAME WELDMENT L/H 20. MOTOR CHAIN RETURN STRIP UHMW 21. DRIVE SPROCKET CHAIN RETURN ANGLE L/H 22.
  • Page 11 NEW LONDON WI 54961 920-982-6600 800-558-3616 Toll Free 920-982-7750 FAX E-MAIL: sales@titanconveyors.com Website: www.titanconveyors.com Contact Your Distributor or Titan Directly for Further Information on Other Titan Conveyor Products Slider bed conveyors  Floor to Floor belt conveyors  parts conveyors ...

Table of Contents