Titan 630 Installation, Maintenance & Parts Manual
Hinged steel belt conveyor
Hide thumbs
Also See for 630:
- Operating manual (84 pages) ,
- Installation, maintenance & parts manual (15 pages)
Table of Contents
Advertisement
Quick Links
Installation, Maintenance & Parts Manual
MODEL 630
Hinged Steel Belt Conveyor
to View the Instructional Videos
"Installing a Hinged Steel Belt Conveyor"
https://youtu.be/HliE9lGVIBM
"Setting Tension on a Hinged Steel Belt"
https://youtu.be/7Za3vqVwjvE
Titan Conveyors
735 Industrial Loop Road
New London, WI 54961
920-982-6600
800-558-3616
FAX 920-982-7750
E-mail: sales@titanconveyors.com
Website: www.titanconveyors.com
Serial No.
Go to Table of Contents
Industrial Conveyor Specialists
For
Advertisement
Table of Contents
Related Manuals for Titan 630
Summary of Contents for Titan 630
- Page 1 Industrial Conveyor Specialists Installation, Maintenance & Parts Manual MODEL 630 Hinged Steel Belt Conveyor to View the Instructional Videos "Installing a Hinged Steel Belt Conveyor" https://youtu.be/HliE9lGVIBM "Setting Tension on a Hinged Steel Belt" https://youtu.be/7Za3vqVwjvE Titan Conveyors 735 Industrial Loop Road...
-
Page 2: Table Of Contents
Page 13 ..............Model 630 Blow Apart Drawing (A) Seller warrants that the material in and the workmanship on the equipment manufactured by TITAN will be free from defects at time of shipment. If during the first year from the date of shipment, the Buyer establishes to the seller’s satisfaction that any part or parts manu- factured by TITAN were defective at the time of shipment, TITAN will, at its own expense, repair or replace (but not install) replacement parts. - Page 3 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
-
Page 4: Introduction
Titan at 920-982-6600. I. RECEIVING Upon delivery of your Titan conveyor, check the packing slip or bill of lading accompanying the unit. If any components are missing, contact Titan IMMEDIATELY with a description of the missing components along with the conveyor serial number(s). -
Page 5: Support Assembly
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S TITAN CONVEYORS TITAN CONVEYORS J3247 J3247 CONVEYOR: CONVEYOR:... -
Page 6: Belt Checklist
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S... - Page 7 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
-
Page 8: Component Checklist
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S... -
Page 9: Motors
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S... - Page 10 VENTILATION - During normal operation gear reducers build up heat and pressure that MUST be vented to protect the seals and gears. If not installed at Titan, a brass vent plug contained in a small plastic bag, will be put in a box or larger bag along with fasteners sent loose for use during field installation.
-
Page 11: Bearings
ONLY compatible polyglycol lubricants should be used. Contact the factory for more information. TEMPERATURE - Most Titan units are supplied with worm gear reducers. These units may run at temperatures between 100 degrees to 200 degrees F. (Higher temperatures are especially common during start up). There is NO NEED TO WORRY unless temperatures exceed 200 degrees F. -
Page 12: V-Belt & Sheaves
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S... - Page 13 V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S MODEL 630 HINGED STEEL BELT MODEL 630 HINGED STEEL BELT CONVEYOR CONVEYOR OUTBOARD BEARING INFEED...