Subscribe to Our Youtube Channel
Related Manuals for Dahua IPC-HF5541F-ZE-S3
Summary of Contents for Dahua IPC-HF5541F-ZE-S3
- Page 1 Box Network Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.0...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the functions, configuration, general operation, and system maintenance of the network camera (hereinafter referred as the Camera). Safety Instructions The following signal words might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury. - Page 3 Quick Start Guide ● Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be opened. ● All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners. ●...
-
Page 4: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings This section introduces content covering the proper handling of the device, hazard prevention, and prevention of property damage. Read carefully before using the device, comply with the guidelines when using it, and keep the manual safe for future reference. Transportation Requirements ●... - Page 5 Quick Start Guide against lightning. For outdoor scenarios, strictly comply with the lightning protection regulations. ● Ground the function earthing portion of the device to improve its reliability (certain models are not equipped with earthing holes). The device is a class I electrical appliance. Make sure that the power supply of the device is connected to a power socket with protective earthing.
- Page 6 Quick Start Guide ● Use the accessories suggested by the manufacturer. Installation and maintenance must be performed by qualified professionals. ● Do not directly touch the photosensitive CMOS. Use an air blower to clean the dust or dirt on the lens.
-
Page 7: Table Of Contents
Quick Start Guide Table of Contents Foreword ........................................I Important Safeguards and Warnings ............................III 1 Introduction ......................................1 1.1 Structure ......................................1 1.2 Connecting Alarm Input/Output ............................3 2 Network Configuration ..................................5 2.1 Initializing the Camera ................................5 2.2 Changing Device IP Address ..............................7 2.3 Logging in to Web Page ................................. -
Page 8: Introduction
Quick Start Guide 1 Introduction 1.1 Structure Structure type might differ depending on different cameras. Figure 1-1 Structure (1) Figure 1-2 Structure (2) Figure 1-3 Structure (3) - Page 9 Quick Start Guide Table 1-1 Structure information Port Name Description ● Outputs analog video signal. It can connect to TV monitor Video output to check image. VIDEO OUT port ● Previews image via the DVR which supports HDCVI when it outputs HDCVI signal.
-
Page 10: Connecting Alarm Input/Output
Quick Start Guide Port Name Description Restores device factory default setup. RESET RESET button When system is running normally, press the RESET button for at least 5 seconds, system can restore factory default setup. Auto back Auto back focus adjustment, by adjusting Sensor board focus position to achieve precise back focus adjustment. - Page 11 Quick Start Guide Figure 1-4 Alarm input Step 2 Connect alarm output device to the alarm output end of the I/O port. The alarm output is relay switch output, which can only connect to OUT_GND alarm devices. N1 and C1 or N2 and C2 constitute a switch to provide the alarm output. The switch is normally open and closed when there is alarm output.
-
Page 12: Network Configuration
Quick Start Guide 2 Network Configuration Device initialization and IP setting can be finished with the ConfigTool or on web page. For more information, see web operation manual. ● Device initialization is available on select models, and it is required at first-time use and after device is reset. - Page 13 Quick Start Guide ● If you select the Current Segment Search checkbox and the Other Segment Search checkbox together, the system searches for the Camera under both conditions. ● Enter username and the password when you want to change IP, configure the system, update the Camera, restart the Camera, and more.
-
Page 14: Changing Device Ip Address
Quick Start Guide Figure 2-3 Device initialization Step 9 Select Easy4ip or select Auto-check for updates as needed. If neither, leave them unselected. Step 10 Click OK to initialize the Camera. Click the success icon ( ) or the failure icon ( ) for the details. -
Page 15: Logging In To Web Page
Quick Start Guide Figure 2-4 Modify IP address Step 3 Select Static mode, and then enter start IP, subnet mask, and gateway. ● IP addresses of multiple cameras will be set to the same if you select the Same IP checkbox. -
Page 16: Installation
Quick Start Guide 3 Installation 3.1 Packing List ● The tool required for the installation such as electric drill is not provided in the package. ● The operation manual and related tool information are contained in the disk or the QR code. Figure 3-1 Packing list 3.2 Dimensions Figure 3-2 Dimensions (mm [inch]) -
Page 17: Installing Housing
Quick Start Guide 3.3.2 Installing housing Use housing if the Camera needs to be installed outdoors, which is to avoid camera damage caused by water soaking. Figure 3-4 Install housing 3.3.3 Installing SD Card ● SD card slot is available on select models. ●... -
Page 18: Attaching The Camera
Quick Start Guide Figure 3-6 Install lens 3.3.5 Attaching the Camera Make sure that the mounting surface is strong enough to hold at least three times the weight of the Camera and bracket. Figure 3-7 Cable going through the side cable tray... -
Page 19: Using I/O Port
Quick Start Guide Figure 3-8 Cable going through the mounting surface 3.3.6 Using I/O Port Step 1 Use a tool like slotted screwdriver to press the I/O button. Step 2 Insert the I/O port. For details about I/O port, see Table 1-1. Step 3 Release the tool after you inserted the I/O port. -
Page 20: Adjusting Lens Angle
Quick Start Guide 3.3.7 Adjusting Lens Angle Figure 3-10 Adjust lens angle... - Page 21 Quick Start Guide...
Need help?
Do you have a question about the IPC-HF5541F-ZE-S3 and is the answer not in the manual?
Questions and answers