Quick Start Guide Foreword General This manual introduces the functions, configuration, general operation, and system maintenance of network camera. Safety Instructions The following signal words might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury.
Page 3
Quick Start Guide ● Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be opened. ● All trademarks, registered trademarks and company names in the manual are properties of their respective owners. ●...
Quick Start Guide Important Safeguards and Warnings Electrical Safety ● All installation and operation shall conform to your local electrical safety codes. ● The power supply must conform to the requirements of ES1 in IEC 62368-1 standard and no higher than PS2. Note that power supply requirements are subject to the device label. ●...
Page 5
Quick Start Guide mild detergent. To avoid possible damage on device body coating which could cause performance decrease, do not use volatile solvent such as alcohol, benzene, diluent to clean the device body, nor can strong, abrasive detergent be used. ●...
Quick Start Guide 1 Introduction 1.1 Cable Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see FAQ manual. Figure 1-1 Component Table 1-1 Lens information Component Description ●...
Quick Start Guide Port name Description Includes alarm signal input and output ports, and the number Alarm I/O of I/O ports might vary on different devices. For detailed information, see Table 1-3. Inputs 12 VDC power. Be sure to supply power as instructed in the manual.
Page 9
Quick Start Guide ● Mode A: Level application. Alarm outputs high and low level, and the alarm outlet is OD, which requires external pull-up resistance (10 K Ohm typical) to work. The maximum external pull-up level is 12 V, maximum port current is 300 mA and the default output signal is high-level (external pull-up voltage).
Quick Start Guide 2 Network Configuration Device initialization and IP setting can be finished with the "ConfigTool" or on web interface. For more information, see web operation manual. ● Device initialization is available on select models, and it is required at first-time use and after device is being reset.
Page 11
Quick Start Guide ● Enter username and the password when you want to change IP, configure the system, update the device, restart the device, and more. Step 5 Click OK. Step 6 Select one or several devices in uninitialized status, and then click Initialize. Step 7 Select the devices to be initialized, and then click Initialize.
Quick Start Guide Figure 2-3 Device initialization Step 9 Select Easy4ip or select Auto-check for updates according to the actual needs. If neither, leave them unselected. Step 10 Click OK to initialize the device. Click the success icon ( ) or the failure icon ( ) for the details.
Quick Start Guide Figure 2-4 Change IP address Select Static mode, and then enter start IP, subnet mask, and gateway. Step 3 ● IP addresses of multiple devices will be set to the same if you select the Same IP checkbox.
Quick Start Guide 3 Installation 3.1 Packing List ● The tool required for the installation such as electric drill is not provided in the package. ● The operation manual and related tool information are contained in the disk or the QR code. Figure 3-1 Packing list 3.2 Dimensions Figure 3-2 Dimensions (unit: mm [inch])
Quick Start Guide 3.3 Installing Camera 3.3.1 Installation Method Figure 3-3 Installation method 3.3.2 Installing SD Card ● SD card slot is available on select models. ● Disconnect the power before installing or removing the SD card. ● Do not open the cover for a long time to avoid spray in cameras. Press the reset button for 10 seconds to reset the device.
Quick Start Guide 3.3.3 Attaching Camera ● Make sure that the mounting surface is strong enough to hold at least three times the weight of the camera and bracket. ● Remove the protective film after finishing installation. Figure 3-5 Cable going through the side cable tray...
Quick Start Guide Figure 3-6 Cable going through the mounting surface 3.3.4 (Optional) Installing Waterproof Connector This part is needed only when a waterproof connector comes with the camera and the camera is used outdoors. Figure 3-7 Install waterproof connector...