Table of Contents
Advertisement
7.2 Initial configuration
When the appliance is connected to the electricity sup-
ply for the first time or following a lengthy power cut,
you need to configure the settings before you can use
it. It may take a few seconds for the settings to appear
in the display.
Press the text field for the required setting.
1.
Possible settings:
– Language
– Clock
– Water hardness
Turn the control ring to change the setting as re-
2.
quired.
Finally, press "Complete the settings" to confirm.
3.
a A note appears in the display confirming that the ini-
tial configuration is complete.
a The time that is set appears on the display.
To check the appliance before heating for the first
4.
time, open and close the appliance door once.
7.3 Cleaning the appliance before using
it for the first time
Clean the cooking compartment and accessories be-
fore using the appliance to prepare food for the first
time.
Remove the product information and the accessor-
1.
ies from the cooking compartment. Remove any
leftover packaging, such as polystyrene pellets, and
the adhesive tape that is in or on the appliance.
8 Basic operation
8.1 Switching on the appliance
Press
to switch the appliance on.
▶
a The Bosch logo appears in the display. The types of
heating then appear.
8.2 Switching off the appliance
Switch your appliance off when you are not using it.
The appliance will switch itself off automatically if it is
not used for a certain period of time.
Press
to switch the appliance off.
▶
a The appliance switches off. Any functions currently
in progress are cancelled.
a The time or residual heat indicator appears in the
display.
8.3 Starting operation
You must start each operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
Do not use the appliance if there is water on the
▶
cooking compartment floor.
Wipe away any water on the cooking compartment
▶
floor before operation.
Wipe the smooth surfaces in the cooking compart-
2.
ment with a soft, damp cloth.
Press
to switch the appliance on.
3.
Fill the water tank.
4.
→ "Filling the water tank", Page 16
Apply the following settings:
5.
Type of heating
Temperature
Added steam
Cooking time
→ "Basic operation", Page 13
Press
to start.
6.
Keep the kitchen ventilated while the appliance is
‒
heating.
a Once the time has elapsed, an audible signal
sounds and the display shows the time as zero.
Press
to switch the appliance off.
7.
Once the appliance has cooled down, clean the
8.
smooth surfaces in the cooking compartment with
soapy water and a dish cloth.
Clean the accessories thoroughly using soapy water
9.
and a dish cloth or soft brush.
Empty the water tank and dry the cooking compart-
10.
ment.
→ "After every steam operation", Page 17
Press
to start.
▶
a The settings, the running time, the display ring and
the heating line appear in the display.
8.4 Pausing or cancelling operation
You can briefly pause operation and then continue. If
you cancel operation completely, the settings will be re-
set.
To pause operation briefly:
1.
Briefly press .
‒
To continue operation, press .
‒
To cancel operation completely, press and hold
2.
for approx. 3 seconds.
a Operation will stop and all the settings will be reset.
8.5 Setting the operating mode
Once you have switched on the appliance, it suggests
an operating mode, e.g. types of heating.
If you want to use a different operating mode to the
1.
one suggested, press
a The list of operating modes is displayed.
→ "Operating modes", Page 9
Press the operating mode that you want to use.
2.
To implement other settings, press the relevant text
3.
fields.
Use the control ring to change the values.
4.
Press
to start.
5.
Basic operation en
4D hot air
Maximum
03
1 hour
.
13
Advertisement
Table of Contents
