Table of Contents
Advertisement
Press "Cooking time".
5.
Use the control ring to set the cooking time.
6.
Press
to start.
7.
Note: If the water tank runs dry during operation, a
notification appears in the display. Operation is
stopped.
→ "Filling the water tank", Page 16
a The appliance starts to heat and the cooking time
counts down.
a When the time has elapsed, a signal sounds. The
time shown in the display is zero.
When the cooking time has elapsed:
8.
To stop the signal early, press any touch field.
‒
To set another cooking time, press "Cooking
‒
time" and use the control ring to set the cooking
time.
When the food is ready, press
‒
appliance off.
Empty the water tank and dry the cooking compart-
9.
ment.
→ "After every steam operation", Page 17
Changing the type of heating
When you change the type of heating, the other set-
tings are also reset.
Press
to pause operation.
1.
Press "Steam".
2.
Press the type of heating that you want to use.
3.
a The corresponding default temperature appears in
the display.
Changing the temperature
Once operation has started, you can change the tem-
perature directly.
Use the control ring to change the temperature.
▶
a The temperature is applied immediately.
Changing the cooking time
You can change the cooking time at any time.
Press.
1.
Use the control ring to change the cooking time.
2.
a The change is applied immediately.
11.3 Steam assistance
When you cook with steam assistance, the appliance
introduces steam into the cooking compartment at vari-
ous intervals. This gives your food a crispy crust and a
shiny surface. Meat stays juicy, tender and only under-
goes a minimum reduction in volume.
Suitable types of heating with steam-assisted
cooking
Only certain types of heating are suitable for operation
with steam-assisted cooking.
You can switch on steam assistance for the following
types of heating:
¡ 4D hot air
¡ Top/bottom heating
¡ Circulated air grilling
¡ Keeping warm
Setting steam-assisted cooking
Requirement: The water tank has been filled.
→ "Filling the water tank", Page 16
Select the "Types of heating" operating mode.
1.
2.
a The temperature is highlighted in white.
3.
4.
5.
6.
to switch the
a The appliance begins to heat up.
a The time, how long the appliance has already been
7.
8.
Changing the steam setting
You can change the steam setting at any time.
1.
2.
a The change is applied immediately.
Changing the temperature
Once operation has started, you can change the tem-
perature directly.
▶
a The temperature is applied immediately.
Changing the type of heating
When you change the type of heating, the other set-
tings will also be reset.
1.
2.
3.
a The corresponding default temperature appears in
11.4 After every steam operation
The remaining water is pumped back into the water
tank after every operation with steam. Then empty and
dry the water tank and the cooking compartment.
Emptying the water tank
The water tank may heat up while the appliance is in
operation.
▶
▶
Press a suitable type of heating.
Use the control ring to set the temperature.
Press "Added steam".
Use the control ring to set the steam setting.
Steam setting
Added steam
0
None
01
Low
02
Medium
03
High
Press
to start.
Note: If the water tank runs dry during operation, a
notification appears in the display. The appliance
continues to operate without added steam.
→ "Filling the water tank", Page 16
in operation, and the settings are shown in the dis-
play.
When the food is ready, press
ance off.
Empty the water tank and dry the cooking compart-
ment.
→ "After every steam operation", Page 17
Press "Added steam".
Use the control ring to change the steam setting.
Use the control ring to change the temperature.
Press
to pause operation.
Press "Types of heating".
Press the type of heating that you want to use.
the display.
WARNING ‒ Risk of burns!
Wait until the water tank has cooled down from the
previous operation.
Remove the water tank from the tank recess.
Steam en
to switch the appli-
17
Advertisement
Table of Contents
